Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Sensor Bus)  


DESCRIPTION

·

The driving support ECU assembly will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to local bus.

·

When the driving support ECU assembly receives a response signal from the ECUs connected to local bus, the driving support ECU assembly recognizes and memorizes that the ECU is connected to local bus. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to local bus when communicating with those ECUs. If the driving support ECU assembly cannot receive response signals from the ECUs that have been memorized as those connected to local bus, the driving support ECU assembly determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U1002 Lost Communication with Gateway Module (Sensor Bus) Driving support ECU assembly cannot receive signals from all ECUs that have been memorized as those connected to local bus.
·

Open or short in local bus CAN main wire or connector

·

Open or short in local bus CAN branch wire or connector

·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

No. 8 CAN junction connector


Driving support ECU assembly

For vehicles with a pre-crash safety system.


WIRING DIAGRAM

C347088E13
1.229,0.979 1.844,1.177 0.615,0.198 10 false CA1P 1.229,1.385 1.844,1.583 0.615,0.198 10 false CA1N 1.719,1.281 2.333,1.479 0.615,0.198 10 false 9 1.729,0.875 2.344,1.073 0.615,0.198 10 false 8 1.26,2.875 1.875,3.073 0.615,0.198 10 false CA1P 1.229,3.521 1.844,3.719 0.615,0.198 10 false CA1N 1.729,3.292 2.344,3.49 0.615,0.198 10 false 6 1.74,2.875 2.354,3.073 0.615,0.198 10 false 5 3.156,2.865 3.771,3.063 0.615,0.198 10 false 7 3.083,3.281 3.698,3.479 0.615,0.198 10 false 18 3.063,1.281 3.677,1.479 0.615,0.198 10 false 16 3.146,0.865 3.76,1.063 0.615,0.198 10 false 5 0.563,1.792 2.51,2.146 1.948,0.354 10 false G168 0.563,1.958 2.51,2.313 1.948,0.354 10 false Driving Support ECU Assembly 5.25,1.781 6.792,2.167 1.542,0.385 10 false G17 5.26,1.958 7.083,2.323 1.823,0.365 10 false Forward Recognition Camera 5.688,0.875 6.302,1.073 0.615,0.198 10 false CANH 5.698,1.51 6.313,1.708 0.615,0.198 10 false CANL 4.042,0.875 4.656,1.073 0.615,0.198 10 false 6 5.458,0.854 6.073,1.052 0.615,0.198 10 false 6 5.406,1.292 6.021,1.49 0.615,0.198 10 false 12 4.042,1.281 4.656,1.479 0.615,0.198 10 false 17 0.5,3.792 2.042,4.177 1.542,0.385 10 false Z6 0.5,3.969 2.042,4.354 1.542,0.385 10 false Millimeter Wave Radar Sensor Assembly 2.896,3.792 4.438,4.177 1.542,0.385 10 false G173 2.896,3.948 4.823,4.365 1.927,0.417 10 false No. 8 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK LOCAL BUS
a.
C339036C08
0.219,2.344 0.729,2.563 0.51,0.219 1.427,0.198 1.938,0.417 0.51,0.219 0.802,0.219 0.958,0.219 0.958,0.219 1.385,0.823 true 0.677,0.448 0.833,0.448 0.833,0.448 1.271,0.844 true 1.24,1.917 1.396,1.917 1.396,1.917 1.646,2.302 true 2.281,2.771 2.563,2.969 2.563,2.969 2.74,2.969 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.115,1.823 0.427,1.979 0.313,0.156 10 false *b 0.333,2.354 0.646,2.51 0.313,0.156 10 false G14 1.521,0.219 1.906,0.406 0.385,0.188 10 false G168 0.417,0.094 0.802,0.281 0.385,0.188 10 false CA1P 0.26,0.333 0.646,0.521 0.385,0.188 10 false CA1N 1.01,1.802 1.396,1.99 0.385,0.188 10 false CG 2.792,2.854 3.177,3.042 0.385,0.188 10 false BAT
*a Component with harness connected
(Driving Support ECU Assembly)
*b Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
G168-8 (CA1P) - G168-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
G168-8 (CA1P) - G168-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G168-8 (CA1P) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G168-9 (CA1N) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G168-8 (CA1P) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
G168-9 (CA1N) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short



Result:
Result Proceed to
OK A
NG
- Open in CAN main wire
B
NG
- Short in CAN bus wire
C
NG
- +B short
- Ground short
D



A

2.CHECK FOR DTC

B

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
2.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is output from driving support ECU assembly A
Other DTC is output B



A

B

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 CAN JUNCTION CONNECTOR)
a.
C266890C89
2.406,1.094 2.813,1.354 0.406,0.26 0.896,0.76 1.104,0.76 1.104,0.76 1.615,1.167 true 0.896,1.635 1.135,1.635 1.135,1.635 1.615,1.302 true 1.083,1.865 1.323,1.865 1.323,1.865 1.708,1.292 true 0.969,0.5 1.177,0.5 1.177,0.5 1.719,1.177 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.438,1.135 2.792,1.323 0.354,0.188 10 false G173 0.344,0.688 0.885,0.875 0.542,0.188 10 false CANH*c 0.365,1.552 0.917,1.75 0.552,0.198 10 false CANL*c 0.552,1.781 1.104,1.979 0.552,0.198 10 false CANL*b 0.406,0.406 0.948,0.594 0.542,0.188 10 false CANH*b
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly


Disconnect the No. 8 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G173-6 (CANH) - G173-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G173-7 (CANH) - G173-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to forward recognition camera CAN main wire) B
NG (to millimeter wave radar sensor assembly CAN main wire) C



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

4.CONNECT CONNECTOR

C

6.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
a.
C268302C36
0.333,1.208 0.771,1.448 0.438,0.24 2.063,1.26 2.344,0.865 2.344,0.865 2.49,0.865 true 2.083,1.521 2.271,1.802 2.271,1.802 2.469,1.802 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.417,1.24 0.729,1.396 0.313,0.156 10 false Q17 2.521,1.708 3.021,1.885 0.5,0.177 10 false CANL 2.552,0.76 3.052,0.938 0.5,0.177 10 false CANH
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-6 (CANH) - Q17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
a.
C333439C30
1.49,0.135 1.979,0.354 0.49,0.219 1.458,1.208 0.906,1.542 0.906,1.542 0.771,1.542 true 1.677,1.229 1.198,1.938 1.198,1.938 1.063,1.938 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.156 2.115,0.354 0.458,0.198 10 false Z6 0.365,1.406 0.979,1.604 0.615,0.198 10 false CA1P 0.646,1.823 1.26,2.021 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-5 (CA1P) - Z6-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.
C266890C90
2.396,1.125 2.917,1.344 0.521,0.219 0.896,0.76 1.104,0.76 1.104,0.76 1.604,1.167 true 0.896,1.635 1.135,1.635 1.135,1.635 1.625,1.292 true 1.083,1.865 1.323,1.865 1.323,1.865 1.708,1.313 true 0.969,0.5 1.177,0.5 1.177,0.5 1.698,1.167 true 2.115,1.833 1.979,1.833 1.979,1.833 1.792,1.281 true 2.313,0.5 2.146,0.5 2.146,0.5 1.792,1.188 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 2.479,1.146 2.906,1.385 0.427,0.24 10 false G173 0.344,0.688 0.885,0.875 0.542,0.188 10 false CANH*d 0.365,1.552 0.917,1.75 0.552,0.198 10 false CANL*d 0.552,1.781 1.104,1.979 0.552,0.198 10 false CANL*c 0.406,0.406 0.948,0.594 0.542,0.188 10 false CANH*c 2.177,1.719 2.729,1.917 0.552,0.198 10 false CANL*b 2.365,0.406 2.906,0.594 0.542,0.188 10 false CANH*b
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to Driving Support ECU Assembly
*c to Forward Recognition Camera
*d to Millimeter Wave Radar Sensor Assembly


Disconnect the No. 8 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G173-5 (CANH) - G173-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-6 (CANH) - G173-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G173-7 (CANH) - G173-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to forward recognition camera CAN main wire) B
NG (to millimeter wave radar sensor assembly CAN main wire) C
NG (to driving support ECU assembly CAN branch wire) D



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

9.CONNECT CONNECTOR

C

11.CONNECT CONNECTOR

D

13.CONNECT CONNECTOR
9.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
a.
C268302C36
0.333,1.208 0.771,1.448 0.438,0.24 2.063,1.26 2.344,0.865 2.344,0.865 2.49,0.865 true 2.083,1.521 2.271,1.802 2.271,1.802 2.469,1.802 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.417,1.24 0.729,1.396 0.313,0.156 10 false Q17 2.521,1.708 3.021,1.885 0.5,0.177 10 false CANL 2.552,0.76 3.052,0.938 0.5,0.177 10 false CANH
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-6 (CANH) - Q17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
a.
C333439C30
1.49,0.135 1.979,0.354 0.49,0.219 1.458,1.208 0.906,1.542 0.906,1.542 0.771,1.542 true 1.677,1.229 1.198,1.938 1.198,1.938 1.063,1.938 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.156 2.115,0.354 0.458,0.198 10 false Z6 0.365,1.406 0.979,1.604 0.615,0.198 10 false CA1P 0.646,1.823 1.26,2.021 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-5 (CA1P) - Z6-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)

13.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
14.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
a.
C338465C07
1.385,0.323 1.969,0.563 0.583,0.24 2.271,1.104 2.49,0.594 2.49,0.594 2.615,0.594 true 2.156,1.115 2.302,0.385 2.302,0.385 2.427,0.385 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.49,0.344 1.854,0.51 0.365,0.167 10 false G168 2.49,0.271 2.99,0.427 0.5,0.156 10 false CA1P 2.677,0.49 3.177,0.646 0.5,0.156 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-8 (CA1P) - G168-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 CAN junction connector.

C300868C46
0.76,0.854 1.271,1.063 0.51,0.208 4,0.875 4.448,1.104 0.448,0.229 2.406,1.375 2.281,1.375 2.281,1.375 1.938,1 true 1.167,1.417 1.302,1.417 1.302,1.417 1.802,1 true 2.417,0.583 2.292,0.583 2.292,0.583 1.969,0.906 true 1.156,0.573 1.292,0.573 1.292,0.573 1.781,0.906 true 4.781,0.458 4.917,0.458 4.917,0.458 5.115,0.771 true 5.969,1.365 5.844,1.365 5.844,1.365 5.594,1.125 true 1.323,0.344 1.458,0.344 1.458,0.344 1.875,0.906 true 1.396,1.635 1.531,1.635 1.531,1.635 1.875,1.01 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 4.104,0.094 4.417,0.25 0.313,0.156 10 false *b 2.469,1.271 3.052,1.438 0.583,0.167 10 false CANL*c 0.771,0.229 1.323,0.396 0.552,0.167 10 false CANH*d 2.469,0.5 3.052,0.667 0.583,0.167 10 false CANH*c 0.875,1.51 1.427,1.677 0.552,0.167 10 false CANL*d 0.844,0.854 1.219,1.031 0.375,0.177 10 false G173 4.521,0.354 4.802,0.5 0.281,0.146 10 false CG 6.021,1.26 6.51,1.479 0.49,0.219 10 false BAT 4.094,0.885 4.406,1.042 0.313,0.156 10 false G14 0.573,0.469 1.125,0.635 0.552,0.167 10 false CANH*e 0.635,1.281 1.188,1.448 0.552,0.167 10 false CANL*e
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b Front view of DLC3
*c to Driving Support ECU Assembly *d to Forward Recognition Camera
*e to Millimeter Wave Radar Sensor Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G173-5 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-16 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-5 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-16 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-17 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-17 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-7 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-18 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G173-7 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G173-18 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to forward recognition camera CAN main wire) B
NG (to millimeter wave radar sensor assembly CAN main wire) C
NG (to driving support ECU assembly CAN branch wire) D



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

16.CONNECT CONNECTOR

C

18.CONNECT CONNECTOR

D

20.CONNECT CONNECTOR
16.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
17.CHECK FOR SHORT IN CAN BUS WIRES (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)
a.
C267485C13
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 2.198,2.917 2.344,3.125 2.344,3.125 2.563,3.125 true 2.073,1.406 2.219,1.615 2.219,1.615 2.438,1.615 true 2.063,1.135 2.208,0.958 2.208,0.958 2.427,0.958 true 1.188,2.135 1.344,2.135 1.344,2.135 1.615,2.458 true 0.083,0.083 0.396,0.25 0.313,0.167 10 false *a 0.167,2.094 0.479,2.25 0.313,0.156 10 false *b 2.615,3.021 2.969,3.208 0.354,0.188 10 false BAT 0.479,2.583 0.833,2.771 0.354,0.188 10 false G14 0.646,1.104 1,1.292 0.354,0.188 10 false Q17 2.49,1.51 2.958,1.698 0.469,0.188 10 false CANL 2.479,0.865 2.948,1.052 0.469,0.188 10 false CANH 0.938,2.021 1.292,2.208 0.354,0.188 10 false CG
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q17-12 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q17-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q14-12 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (FORWARD RECOGNITION CAMERA - NO. 8 CAN JUNCTION CONNECTOR)

18.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

19.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
19.CHECK FOR SHORT IN CAN BUS WIRES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
a.
C339037C04
0.25,2.396 0.719,2.646 0.469,0.25 2.51,0.625 2.979,0.875 0.469,0.25 0.896,1.396 1.052,1.396 1.052,1.396 1.469,1.01 true 1.208,1.688 1.365,1.688 1.365,1.688 1.635,1.021 true 1.292,1.917 1.448,1.917 1.448,1.917 1.656,2.302 true 2.313,2.771 2.573,3.021 2.573,3.021 2.75,3.021 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.115,1.833 0.427,1.99 0.313,0.156 10 false *b 0.354,2.417 0.667,2.573 0.313,0.156 10 false G14 2.656,0.635 2.969,0.792 0.313,0.156 10 false Z6 0.51,1.271 0.948,1.448 0.438,0.177 10 false CA1P 0.823,1.552 1.26,1.729 0.438,0.177 10 false CA1N 1.031,1.802 1.469,1.979 0.438,0.177 10 false CG 2.802,2.885 3.24,3.063 0.438,0.177 10 false BAT
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-5 (CA1P) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Z6-6 (CA1N) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Z6-5 (CA1P) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z6-6 (CA1N) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)

20.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

21.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
21.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)
a.
C339038C03
0.406,2.604 0.865,2.844 0.458,0.24 1.479,0.323 1.938,0.563 0.458,0.24 1.104,2.156 1.281,2.156 1.281,2.156 1.667,2.563 true 2.115,1.083 2.365,0.354 2.365,0.354 2.542,0.354 true 2.24,1.104 2.646,0.667 2.646,0.667 2.823,0.667 true 2.188,2.948 2.375,3.188 2.375,3.188 2.552,3.188 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.083,1.885 0.396,2.042 0.313,0.156 10 false *b 1.531,0.344 1.958,0.531 0.427,0.188 10 false G168 0.49,2.615 0.917,2.802 0.427,0.188 10 false G14 2.594,0.25 3.021,0.438 0.427,0.188 10 false CA1P 2.885,0.552 3.313,0.74 0.427,0.188 10 false CA1N 0.833,2.021 1.26,2.208 0.427,0.188 10 false CG 2.615,3.073 3.042,3.26 0.427,0.188 10 false BAT
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3


Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-8 (CA1P) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G168-9 (CA1N) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G168-8 (CA1P) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G168-9 (CA1N) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)