Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected by the LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1532 LVDS Signal Malfunction (from Extension Module) When one of the conditions below is met:
·

Video signal (digital) is lost.

·

Navigation ECU is/was not connected while the ignition switch is/was to ON or ACC.

·

Communication between the master unit and the navigation ECU is/was not possible when the engine is/was started.


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

No. 1 navigation wire



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E292617E03
1.76,0.688 2.219,0.885 0.458,0.198 10 false +B2 1.677,1.094 2.135,1.292 0.458,0.198 10 false ACC2 1.656,1.479 2.115,1.677 0.458,0.198 10 false GND2 1.656,1.885 2.115,2.083 0.458,0.198 10 false LVDS 0.615,2.354 2.333,2.677 1.719,0.323 10 false Radio and Display Receiver Assembly 2.208,1.896 2.667,2.094 0.458,0.198 10 false Y2 2.229,1.5 2.688,1.698 0.458,0.198 10 false Y1 2.219,1.104 2.677,1.302 0.458,0.198 10 false Y1 2.219,0.698 2.677,0.896 0.458,0.198 10 false Y1 2.26,0.49 2.719,0.688 0.458,0.198 10 false 4 2.26,0.917 2.719,1.115 0.458,0.198 10 false 3 2.26,1.302 2.719,1.5 0.458,0.198 10 false 8 2.25,1.698 2.708,1.896 0.458,0.198 10 false 1 2.833,2.469 4.615,2.74 1.781,0.271 10 false No. 1 Navigation Wire 0.865,3.229 3.125,3.417 2.26,0.188 10 false : LVDS Communication Line 4.865,0.51 5.323,0.708 0.458,0.198 10 false 1 4.885,0.906 5.344,1.104 0.458,0.198 10 false 3 4.896,1.302 5.354,1.5 0.458,0.198 10 false 2 4.906,1.708 5.365,1.906 0.458,0.198 10 false 1 4.833,0.708 5.292,0.906 0.458,0.198 10 false Y5 4.833,1.094 5.292,1.292 0.458,0.198 10 false Y5 4.844,1.49 5.302,1.688 0.458,0.198 10 false Y5 4.833,1.885 5.292,2.083 0.458,0.198 10 false Y6 5.198,2.375 6.531,2.615 1.333,0.24 10 false Navigation ECU 5.208,0.688 5.469,0.875 0.26,0.188 10 false B+ 5.229,1.083 5.688,1.281 0.458,0.198 10 false ACC 5.219,1.49 5.677,1.688 0.458,0.198 10 false GND 5.219,1.896 5.677,2.094 0.458,0.198 10 false LVDS

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK NO. 1 NAVIGATION WIRE (NAVIGATION ECU POWER SOURCE)
a.
E291690C03
1.531,0.333 1.927,0.563 0.396,0.229 0.625,1.594 0.771,1.594 0.771,1.594 0.958,1.063 true 0.823,1.865 0.969,1.865 0.969,1.865 1.115,1.042 true 1.729,1.875 1.573,1.875 1.573,1.875 1.365,1.052 true 0.094,0.042 0.406,0.198 0.313,0.156 10 false *a 0.396,1.521 0.635,1.677 0.24,0.156 10 false B+ 0.458,1.792 0.938,1.958 0.479,0.167 10 false GND 1.813,1.792 2.292,1.958 0.479,0.167 10 false ACC 1.625,0.375 2.104,0.542 0.479,0.167 10 false Y5
*a Front view of wire harness connector
(to Navigation ECU)


Disconnect the navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y5-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y5-1 (B+) - Y5-2 (GND) Always 11 to 14 V
Y5-3 (ACC) - Y5-2 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.REPLACE NO. 1 NAVIGATION WIRE (LVDS COMMUNICATION LINE)

NG

3.CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
2.REPLACE NO. 1 NAVIGATION WIRE (LVDS COMMUNICATION LINE)
a.

Replace the No. 1 navigation wire (LVDS communication line).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 NAVIGATION WIRE [LVDS COMMUNICATION LINE] IS DEFECTIVE)

NG

4.REPLACE NAVIGATION ECU
3.CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the Y1 radio and display receiver assembly connector.


b.

Disconnect the Y5 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-4 (+B2) - Y5-1 (B+) Always Below 1 Ω
Y1-3 (ACC2) - Y5-3 (ACC) Always Below 1 Ω
Y1-8 (GND2) - Y5-2 (GND) Always Below 1 Ω
Y1-4 (+B2) - Body ground Always 10 kΩ or higher
Y1-3 (ACC2) - Body ground Always 10 kΩ or higher
Y1-8 (GND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

NG

4.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY