Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the battery voltage drops.
·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E307660E01
3.323,1.479 3.781,1.656 0.458,0.177 10 false RADIO 1.552,1.302 2.51,1.5 0.958,0.198 10 false from Battery 4.781,2.104 6.458,2.479 1.677,0.375 10 false Radio and Display Receiver Assembly 4.771,1.927 5.167,2.104 0.396,0.177 10 false G141 5.25,1.292 5.573,1.469 0.323,0.177 10 false +B1 5.073,1.188 5.229,1.354 0.156,0.167 10 false 4 0.365,0.563 2.365,0.74 2,0.177 10 false from Engine Stop and Start ECU 3.135,0.448 3.344,0.625 0.208,0.177 10 false *1 2.906,1.188 3.115,1.365 0.208,0.177 10 false *2 0.146,2.042 2.031,2.24 1.885,0.198 10 false *1: w/ Stop and Start System 0.146,2.375 2.031,2.573 1.885,0.198 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Check that the battery voltage.

Standard voltage:

11 to 14 V


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
2.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.
E277492C26
1.396,0.25 1.917,0.531 0.521,0.281 2.281,0.927 2.594,0.573 2.594,0.573 2.823,0.573 true 2.917,0.49 3.281,0.74 0.365,0.25 10 false +B1 1.51,0.313 2.01,0.552 0.5,0.24 10 false G141 0.146,0.063 0.458,0.219 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground*1 Always 9.5 to 14 V
G141-4 (+B1) - Body ground*2 Always 11 to 14 V


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Proceed to
OK
NG



OK

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR