Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation ECU. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E294735E04
0.656,0.417 1.083,0.573 0.427,0.156 10 false UDO- 0.667,0.844 1.094,1 0.427,0.156 10 false UDO+ 0.667,1.302 1.094,1.458 0.427,0.156 10 false UJSG 0.792,1.74 1.219,1.896 0.427,0.156 10 false UPI 0.667,2.188 1.094,2.344 0.427,0.156 10 false UJSS 0.156,2.5 0.583,2.656 0.427,0.156 10 false G145 0.156,2.656 2.583,2.833 2.427,0.177 10 false No. 1 Stereo Jack Adapter Assembly 0.823,3.177 3.521,3.354 2.698,0.177 10 false : Data Signal (USB Communication Line) 1.156,0.302 1.583,0.458 0.427,0.156 10 false 2 1.156,0.729 1.583,0.885 0.427,0.156 10 false 3 1.167,1.198 1.594,1.354 0.427,0.156 10 false 4 1.177,1.625 1.604,1.781 0.427,0.156 10 false 1 1.188,2.073 1.615,2.229 0.427,0.156 10 false 5 3.625,2.375 4.052,2.531 0.427,0.156 10 false *3 5.906,0.302 6.063,0.448 0.156,0.146 10 false 2 5.906,0.74 6.083,0.917 0.177,0.177 10 false 3 5.917,1.208 6.083,1.375 0.167,0.167 10 false 4 5.917,1.656 6.083,1.802 0.167,0.146 10 false 1 5.927,2.083 6.073,2.229 0.146,0.146 10 false 5 6.146,0.531 6.688,0.708 0.542,0.177 10 false US1-*2 6.135,0.99 6.698,1.167 0.563,0.177 10 false US1+*2 6.135,1.427 6.698,1.604 0.563,0.177 10 false UGD1*2 6.135,1.865 6.677,2.063 0.542,0.198 10 false USV1*2 6.115,2.177 6.677,2.344 0.563,0.167 10 false USG1 5.896,2.521 6.417,2.698 0.521,0.177 10 false G198*1 5.896,2.698 6.99,2.885 1.094,0.188 10 false Navigation ECU 3.708,3.469 5.198,3.625 1.49,0.156 10 false *3: Shielded 6.385,2.521 6.906,2.698 0.521,0.177 10 false G199*2 6.135,0.354 6.677,0.531 0.542,0.177 10 false UDO-*1 6.135,0.813 6.698,0.99 0.563,0.177 10 false UDO+*1 6.125,1.26 6.688,1.438 0.563,0.177 10 false UESG*1 6.135,1.698 6.604,1.865 0.469,0.167 10 false UPO*1 0.208,3.458 1.698,3.615 1.49,0.156 10 false *1: for RHD 3.708,3.198 5.198,3.354 1.49,0.156 10 false *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to before play begins.

·

When using a USB device, files that are copy protected or encrypted cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>SYSTEM DESCRIPTION



Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B



A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G198*1 or G199*2 navigation ECU connector.

*1: for RHD

*2: for LHD



b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G198-1 (UPO) - G145-1 (UPI) Always Below 1 Ω
G198-2 (UDO-) - G145-2 (UDO-) Always Below 1 Ω
G198-3 (UDO+) - G145-3 (UDO+) Always Below 1 Ω
G198-4 (UESG) - G145-4 (UJSG) Always Below 1 Ω
G198-5 (USG1) - G145-5 (UJSS) Always Below 1 Ω
G198-1 (UPO) - Body ground Always 10 kΩ or higher
G198-2 (UDO-) - Body ground Always 10 kΩ or higher
G198-3 (UDO+) - Body ground Always 10 kΩ or higher
G198-4 (UESG) - Body ground Always 10 kΩ or higher
G198-5 (USG1) - Body ground Always 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G199-1 (USV1) - G145-1 (UPI) Always Below 1 Ω
G199-2 (US1-) - G145-2 (UDO-) Always Below 1 Ω
G199-3 (US1+) - G145-3 (UDO+) Always Below 1 Ω
G199-4 (UGD1) - G145-4 (UJSG) Always Below 1 Ω
G199-5 (USG1) - G145-5 (UJSS) Always Below 1 Ω
G199-1 (USV1) - Body ground Always 10 kΩ or higher
G199-2 (US1-) - Body ground Always 10 kΩ or higher
G199-3 (US1+) - Body ground Always 10 kΩ or higher
G199-4 (UGD1) - Body ground Always 10 kΩ or higher
G199-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION ECU
a.
E226479C28
1.5,0.917 1.99,1.208 0.49,0.292 1.958,2.083 2.396,2.26 2.396,2.26 2.552,2.26 true 1.5,2.083 1.042,2.25 1.042,2.25 0.865,2.25 true 2.594,2.188 3.021,2.333 0.427,0.146 10 false UJSG 0.542,2.177 0.813,2.323 0.271,0.146 10 false UPI 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a 1.583,0.979 2.052,1.167 0.469,0.188 10 false G145
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Reconnect the G198*1 or G199*2 navigation ECU connector.

·

*1: for RHD

*2: for LHD



b.

Disconnect the No. 1 stereo jack adapter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G145-1 (UPI) - G145-4 (UJSG) Ignition switch ACC 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/ restore it.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.



b.

Save the data again and check if it can be played on the in-vehicle device.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (USB OR "iPod" IS DEFECTIVE)

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if USB device or "iPod" is recognized by navigation ECU, or if information such as track, artist and album names is displayed on screen.

OK:

USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" IS INCOMPATIBLE OR DEFECTIVE

NG