Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E289276E06
0.896,1.063 1.354,1.26 0.458,0.198 10 false AUXO 0.969,1.542 1.427,1.74 0.458,0.198 10 false ARO 0.99,2.01 1.448,2.208 0.458,0.198 10 false ALO 0.885,2.479 1.344,2.677 0.458,0.198 10 false ASGN 0.885,2.969 1.344,3.167 0.458,0.198 10 false AGND 5.979,1.063 6.438,1.26 0.458,0.198 10 false ADPG 5.969,1.51 6.427,1.708 0.458,0.198 10 false VAR+ 5.979,2 6.438,2.198 0.458,0.198 10 false VAL+ 5.969,2.49 6.427,2.688 0.458,0.198 10 false VA- 5.979,2.979 6.438,3.177 0.458,0.198 10 false AGND 5.698,0.938 5.906,1.146 0.208,0.208 10 false 25 5.698,1.406 5.906,1.615 0.208,0.208 10 false 26 5.688,1.906 5.896,2.115 0.208,0.208 10 false 28 5.698,2.365 5.906,2.573 0.208,0.208 10 false 27 5.708,2.865 5.917,3.073 0.208,0.208 10 false 11 1.375,0.969 1.583,1.177 0.208,0.208 10 false 8 1.385,1.458 1.594,1.667 0.208,0.208 10 false 5 1.385,1.917 1.594,2.125 0.208,0.208 10 false 6 1.385,2.375 1.594,2.583 0.208,0.208 10 false 7 1.385,2.865 1.521,3.052 0.135,0.188 10 false 9 0.385,3.448 0.844,3.646 0.458,0.198 10 false G145 0.375,3.615 2.01,3.958 1.635,0.344 10 false No. 1 Stereo Jack Adapter Assembly 5.354,3.385 5.813,3.583 0.458,0.198 10 false G143 5.365,3.552 7.052,3.948 1.688,0.396 10 false Radio and Display Receiver Assembly 2.865,3.177 3.219,3.375 0.354,0.198 10 false * 4.396,3.177 4.74,3.375 0.344,0.198 10 false * 0.333,4.375 1.958,4.583 1.625,0.208 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G145-6 (ALO) - G143-28 (VAL+) Always Below 1 Ω
G145-5 (ARO) - G143-26 (VAR+) Always Below 1 Ω
G145-7 (ASGN) - G143-27 (VA-) Always Below 1 Ω
G145-9 (AGND) - G143-11 (AGND) Always Below 1 Ω
G145-8 (AUXO) - G143-25 (ADPG) Always Below 1 Ω
G145-6 (ALO) - Body ground Always 10 kΩ or higher
G145-5 (ARO) - Body ground Always 10 kΩ or higher
G145-9 (ASGN) - Body ground Always 10 kΩ or higher
G145-9 (AGND) - Body ground Always 10 kΩ or higher
G145-8 (AUXO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR