Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Data Signal Circuit between Stereo Jack Adapter and Extension Module  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation ECU via this circuit.

WIRING DIAGRAM

E294736E04
1.563,0.74 2.021,0.896 0.458,0.156 10 false UDO- 1.531,1.323 1.99,1.479 0.458,0.156 10 false UDO+ 2.063,0.604 2.521,0.76 0.458,0.156 10 false 2 2.094,1.167 2.552,1.323 0.458,0.156 10 false 3 0.917,1.771 1.375,1.927 0.458,0.156 10 false G145 0.938,1.948 3.396,2.156 2.458,0.208 10 false No. 1 Stereo Jack Adapter Assembly 0.813,2.354 3.458,2.563 2.646,0.208 10 false : Data Signal (USB Communication Line) 5.219,0.833 5.75,1.021 0.531,0.188 10 false US1-*2 5.198,1.219 5.771,1.406 0.573,0.188 10 false UDO+*1 4.958,0.615 5.417,0.771 0.458,0.156 10 false 2 4.958,1.167 5.417,1.323 0.458,0.156 10 false 3 5.01,1.771 5.51,1.927 0.5,0.156 10 false G198*1 5.031,1.938 6.083,2.135 1.052,0.198 10 false Navigation ECU 5.542,1.771 6.042,1.927 0.5,0.156 10 false G199*2 0.198,2.563 0.979,2.75 0.781,0.188 10 false *1: for RHD 1,2.563 1.781,2.75 0.781,0.188 10 false *2: for LHD 5.208,0.656 5.74,0.833 0.531,0.177 10 false UDO-*1 5.208,1.406 5.75,1.583 0.542,0.177 10 false US1+*2

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G198*1 or G199*2 navigation ECU connector.

·

*1: for RHD

*2: for LHD



b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G198-2 (UDO-) - G145-2 (UDO-) Always Below 1 Ω
G198-3 (UDO+) - G145-3 (UDO+) Always Below 1 Ω
G198-2 (UDO-) - Body ground Always 10 kΩ or higher
G198-3 (UDO+) - Body ground Always 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G199-2 (US1-) - G145-2 (UDO-) Always Below 1 Ω
G199-3 (US1+) - G145-3 (UDO+) Always Below 1 Ω
G199-2 (US1-) - Body ground Always 10 kΩ or higher
G199-3 (US1+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR