Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


SYSTEM DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E280972E05
0.75,1.813 1.667,2.01 0.917,0.198 10 false M32 1.781,0.74 1.938,0.938 0.156,0.198 10 false 1 5.313,0.76 5.719,0.958 0.406,0.198 10 false 16 5.573,0.885 6.115,1.115 0.542,0.229 10 false MUT1 1.271,0.875 1.75,1.094 0.479,0.219 10 false MUTE 5.219,1.792 5.708,2.01 0.49,0.219 10 false G143 5.24,1.948 6.948,2.292 1.708,0.344 10 false Radio and Display Receiver Assembly 0.74,1.969 2.469,2.292 1.729,0.323 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C15
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 true 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.854 2.24,1.021 0.646,0.167 10 false M32 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M32-1 (MUTE) - Body ground Ignition switch ACC, audio system playing→ Changing modes Above 3.5 V→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-16 (MUT1) - M32-1 (MUTE) Always Below 1 Ω
G143-16 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.
E221772C09
1.49,0.698 1.948,0.979 0.458,0.281 1.073,2.208 1.323,2.865 true 1.552,0.76 2.042,0.958 0.49,0.198 10 false G143 1.229,2.875 1.906,3.063 0.677,0.188 10 false MUT1 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-16 (MUT1) - Body ground Ignition switch ACC, audio system playing→ Changing modes Above 3.5 V→ Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY