Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E333568E03
2.573,1.521 2.885,1.698 0.313,0.177 10 false M32 2.563,1.667 5.302,1.844 2.74,0.177 10 false Stereo Component Amplifier Assembly 3.26,0.729 3.552,0.896 0.292,0.167 10 false TX+ 3.271,1.125 3.563,1.292 0.292,0.167 10 false TX- 3.625,0.573 3.771,0.729 0.146,0.156 10 false 8 3.635,0.979 3.781,1.135 0.146,0.156 10 false 7 5.177,0.729 5.573,0.906 0.396,0.177 10 false G143 5.167,1.125 5.563,1.302 0.396,0.177 10 false G143 5.615,0.719 5.979,0.885 0.365,0.167 10 false TX1+ 5.615,1.146 5.938,1.313 0.323,0.167 10 false TX1- 5.479,3.76 6.688,4.115 1.208,0.354 10 false Radio and Display Receiver Assembly 2.542,3.563 3.458,3.74 0.917,0.177 10 false a2 3.281,2.771 3.573,2.938 0.292,0.167 10 false TX+ 3.292,3.146 3.583,3.313 0.292,0.167 10 false TX- 5.615,2.75 5.979,2.917 0.365,0.167 10 false TX3+ 5.625,3.156 5.948,3.323 0.323,0.167 10 false TX3- 5.177,2.76 5.573,2.938 0.396,0.177 10 false G158 5.167,3.156 5.563,3.333 0.396,0.177 10 false G158 2.5,3.708 3.896,3.906 1.396,0.198 10 false Parking Assist ECU 2.156,0.323 2.302,0.479 0.146,0.156 10 false *1 2.167,2.385 2.313,2.542 0.146,0.156 10 false *2 0.281,3.135 1.74,3.333 1.458,0.198 10 false *1: for 11 speakers 0.313,3.51 1.74,3.854 1.427,0.344 10 false *2: w/ Panoramic View Monitor System 0.969,4.344 3.01,4.531 2.042,0.188 10 false : AVC-LAN communication Line 5.271,2.969 5.417,3.125 0.146,0.156 10 false 8 3.635,3.01 3.781,3.167 0.146,0.156 10 false 9 3.604,2.604 3.854,2.771 0.25,0.167 10 false 10 5.281,2.563 5.427,2.719 0.146,0.156 10 false 7 5.281,0.927 5.427,1.083 0.146,0.156 10 false 8 5.271,0.521 5.417,0.677 0.146,0.156 10 false 7

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.INSPECT RADIO & DISPLAY RECEIVER ASSEMBLY
a.
E333569C01
1.51,1.177 1.26,0.615 1.26,0.615 1.115,0.615 true 1.667,1.198 1.885,0.635 1.885,0.635 2.01,0.635 true 1.635,3.448 1.385,2.885 1.385,2.885 1.24,2.885 true 1.771,3.448 1.979,2.917 1.979,2.917 2.115,2.917 true 0.073,0.031 0.271,0.229 0.198,0.198 10 false *a 0.656,0.531 1.25,0.719 0.594,0.188 10 false TX3-*A 2.094,0.563 2.688,0.75 0.594,0.188 10 false TX3+*A 0.771,2.802 1.365,2.99 0.594,0.188 10 false TX1-*B 2.188,2.823 2.781,3.01 0.594,0.188 10 false TX1+*B
*A w/ Panoramic View Monitor System
*B for 11 Speakers
*a Component without harness connected (Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panoramic View Monitor System:
Tester Connection Condition Specified Condition
7 (TX3+) - 8 (TX3-) Always 60 to 80 Ω

for 11 Speakers:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

*1: for 11 Speakers

*2: w/ Panoramic View Monitor System


a.

Disconnect the G143 and G158 radio and display receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.*1


c.

Disconnect the a2 parking assist ECU connector.*2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 11 Speakers:
Tester Connection Condition Specified Condition
M32-8 (TX+) - G143-7 (TX1+) Always Below 1 Ω
M32-7 (TX-) - G143-8 (TX1-) Always Below 1 Ω
M32-8 (TX+) - Body ground Always 10 kΩ or higher
M32-7 (TX-) - Body ground Always 10 kΩ or higher

w/ Panoramic View Monitor System:
Tester Connection Condition Specified Condition
a2-10 (TX+) - G158-7 (TX3+) Always Below 1 Ω
a2-9 (TX-) - G158-8 (TX3-) Always Below 1 Ω
a2-10 (TX+) - Body ground Always 10 kΩ or higher
a2-9 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY