Home › Engine / Hybrid System › 2AD-FHV COOLING › COOLING FAN ECU › from 2015.10
RM3090E _51 Engine / Hybrid System _008738 2AD-FHV COOLING _0223443 COOLING FAN ECU G

2AD-FHV COOLING  COOLING FAN ECU  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89257 1.INSPECT COOLING FAN ECU

a.

Check and ensure the following conditions:

i.

The power switch is off.


ii.

The engine coolant temperature is less than 92°C (198°F).


iii.

The auxiliary battery voltage is between 11 to 14 V.


iv.

The A/C switch is off.



b.

Connect the pickup of a clamp-on ammeter around 1 of the 2 wires for the cooling fan motor.


c.

Turn the power switch on (IG) and wait for approximately 10 seconds. Check that the fan does not operate.


d.

Start the engine. Check that the fan does not operate with the engine idling.

HINT:
·

Make sure that the engine coolant temperature is less than 92°C (198°F).


·

Turn the A/C switch off.




e.

Check that the fan operates when the A/C switch is turned on.

Standard Current:
w/ Towing Package
Item Condition Specified Condition
Cooling fan motor Auxiliary battery voltage applied at 20°C (68°F) 15.5 to 21.5 A
No. 2 cooling fan motor 15.5 to 21.5 A

w/o Towing Package
Item Condition Specified Condition
Cooling fan motor Auxiliary battery voltage applied at 20°C (68°F) 10.6 to 16.6 A
No. 2 cooling fan motor 10.6 to 16.6 A


HINT:

Make sure that the engine coolant temperature is less than 92°C (198°F).



f.

Check that the fan operates when the engine coolant temperature sensor connector is disconnected.

Standard Current:
w/ Towing Package
Item Condition Specified Condition
Cooling fan motor Auxiliary battery voltage applied at 20°C (68°F) 15.5 to 21.5 A
No. 2 cooling fan motor 15.5 to 21.5 A

w/o Towing Package
Item Condition Specified Condition
Cooling fan motor Auxiliary battery voltage applied at 20°C (68°F) 10.6 to 16.6 A
No. 2 cooling fan motor 10.6 to 16.6 A



g.
A284427C02
0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.698,0.635 2.01,0.833 0.313,0.198 10 false *b 0.396,1.698 0.708,1.896 0.313,0.198 10 false *d 0.406,1.146 0.719,1.344 0.313,0.198 10 false *c 1.438,3.698 1.75,3.896 0.313,0.198 10 false 94 1.063,3.698 1.375,3.896 0.313,0.198 10 false 92 2.344,3.708 2.656,3.906 0.313,0.198 10 false 99 2.573,3.708 2.885,3.906 0.313,0.198 10 false 100 2.875,3.708 3.188,3.906 0.313,0.198 10 false 102 1.99,3.708 2.302,3.906 0.313,0.198 10 false 97 0.417,2.552 0.729,2.75 0.313,0.198 10 false *e 0.438,3.104 0.75,3.302 0.313,0.198 10 false *f 0.167,2.104 0.479,2.302 0.313,0.198 10 false *g 1.01,3.906 1.323,4.104 0.313,0.198 10 false 198 1.396,3.906 1.708,4.104 0.313,0.198 10 false 201 1.938,3.917 2.25,4.115 0.313,0.198 10 false 207 2.302,3.917 2.615,4.115 0.313,0.198 10 false 210 2.583,3.917 2.896,4.115 0.313,0.198 10 false 212 2.875,3.917 3.188,4.115 0.313,0.198 10 false 216 3.115,3.698 3.427,3.896 0.313,0.198 10 false (°C) 3.115,3.906 3.417,4.135 0.302,0.229 10 false (°F)
*a Operating Diagram
*b A/C OFF
*c MAX HI
*d HI
*e LO
*f MAX LO
*g Fan Speed


After the engine is warmed up, check that the fan operates as shown in the illustration.

HINT:
·

The engine coolant temperature at which the fan starts operating is approximately 94°C (201°F).

·

This system can also be checked using the GTS.

·

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.



Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8