Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0224930 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0101  Lost Communication with TCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0129  Lost Communication with Brake System Control Module  U0142  Lost Communication with Body Control Module "B"  U0155  Lost Communication with Combination Meter  


DESCRIPTION

These DTCs are stored when a communication error occurs between the sensors and ECUs.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A" While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the ECM and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

ECM

·

Forward recognition camera


U0101 Lost Communication with TCM While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the ECM (TCM) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

ECM (TCM)

·

Forward recognition camera


U0123 Lost Communication with Yaw Rate Sensor Module While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the yaw rate sensor and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Forward recognition camera


U0129 Lost Communication with Brake System Control Module While the ignition switch is ON, a communication error between the skid control ECU and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Forward recognition camera


U0142 Lost Communication with Body Control Module "B" While the ignition switch is ON, a communication error between the main body ECU (multiplex network body ECU) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera


U0155 Lost Communication with Combination Meter While the ignition switch is ON, a communication error between the combination meter assembly and the forward recognition camera is detected for approximately 50 seconds or more.
·

CAN communication system

·

Combination meter assembly

·

Forward recognition camera



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CLEAR DTCs (ROAD SIGN ASSIST SYSTEM)

B

2.CLEAR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

Result:
Proceed to
NEXT



NEXT

3.CHECK CAN COMMUNICATION SYSTEM
3.CHECK CAN COMMUNICATION SYSTEM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: System Select / Can Bus Check / Enter.

OK:

The CAN communication system is normal.



Result:
Proceed to
OK
NG



OK

NG