Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.10–2016.08
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


C279757C11
2.083,0.521 2.417,0.75 0.333,0.229 2.083,0.938 2.417,1.167 0.333,0.229 0.094,0.052 0.406,0.25 0.313,0.198 10 *a 2.125,0.563 2.583,0.76 0.458,0.198 10 M11 2.125,0.979 2.583,1.177 0.458,0.198 10 M30 2.438,0.469 2.75,0.667 0.313,0.198 10 *A 2.438,0.885 2.75,1.083 0.313,0.198 10 *B
*A for Air Bag Caution Label with "9L" Identification Mark *B except Air Bag Caution Label with "9L" Identification Mark
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
- -


a.

Disconnect the tire pressure warning ECU and receiver M11*1 or M30*2 connector and measure the voltage or resistance on the wire harness side.

*1: for Air Bag Caution Label with "9L" Identification Mark

*2: except Air Bag Caution Label with "9L" Identification Mark


for Air Bag Caution Label with "9L" Identification Mark
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-1 (IG) - M11-12 (E) L - W-B IG power source Ignition switch ON 10 to 16 V
M11-7 (+B) - M11-12 (E) R - W-B Power supply (from battery) Always 10 to 16 V
M11-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

except Air Bag Caution Label with "9L" Identification Mark
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M30-1 (IG) - M30-12 (GND) L - W-B IG power source Ignition switch ON 10 to 16 V
M30-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Connect the tire pressure warning ECU and receiver M11*1 or M30*2 connector.

*1: for Air Bag Caution Label with "9L" Identification Mark

*2: except Air Bag Caution Label with "9L" Identification Mark



c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may have a malfunction.

HINT:

Inspect the connectors from the back side while the connectors are connected.


E129452C25
1.333,0.844 1.729,1.115 0.396,0.271 1.333,0.479 1.729,0.75 0.396,0.271 1.948,0.542 2.26,0.698 0.313,0.156 10 *A 1.938,0.917 2.25,1.073 0.313,0.156 10 *B 0.188,0.115 0.5,0.271 0.313,0.156 10 *a 1.396,0.531 1.854,0.729 0.458,0.198 10 M11 1.396,0.906 1.854,1.104 0.458,0.198 10 M30
*A for Air Bag Caution Label with "9L" Identification Mark *B except Air Bag Caution Label with "9L" Identification Mark
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -


for Air Bag Caution Label with "9L" Identification Mark
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-3 (CLSW) - M11-12 (E) V - W-B Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch ON


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch OFF


8 to 15 V
M11-4 (RDA) - M11-12 (E) G - W-B Output signals Ignition switch ON Pulse generation (see waveform 1)
M11-5 (PRG) - M11-12 (E) W - W-B Input signals Ignition switch ON Pulse generation (see waveform 1)

except Air Bag Caution Label with "9L" Identification Mark
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M30-3 (CLSW) - M30-12 (GND) V - W-B Tire pressure warning reset switch
·

Ignition switch ON

·

Tire pressure warning reset switch ON


Below 1.5 V
·

Ignition switch ON

·

Tire pressure warning reset switch OFF


8 to 15 V
M30-4 (RDA2) - M30-12 (GND) G - W-B Output signals Ignition switch ON Pulse generation (see waveform 1)
M30-5 (PRG2) - M30-12 (GND) W - W-B Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058C02
2.875,1.219 3.115,1.427 0.24,0.208 10 *b 0.104,0.083 0.313,0.302 0.208,0.219 10 *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal M11-4 (RDA) - M11-12 (E)*1
M11-5 (PRG) - M11-12 (E)*1
M30-4 (RDA2) - M30-12 (GND)*2
M30-5 (PRG2) - M30-12 (GND)*2
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

*1: for Air Bag Caution Label with "9L" Identification Mark

*2: except Air Bag Caution Label with "9L" Identification Mark


HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.