Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY › 2015.10–2016.08
RM3090E _52 Drivetrain _008760 GF1A TRANSFER / 4WD / AWD _0050209 TRANSFER ASSEMBLY A

GF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before installation of each part, thoroughly clean and dry it. Then apply grease or oil as necessary. Do not use alkaline chemicals to clean aluminum parts, rubber parts or precoated bolts. Also, do not use non-residue solvent or other cleaning oils to clean O-rings, oil seals or rubber parts.


PROCEDURE

Hide 36100A 1.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.
C277113C01
0.156,0.208 0.344,0.365 0.188,0.156 10 *A 0.167,2.552 0.479,2.75 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


Using 2 nuts, remove the 4 transfer and transaxle setting stud bolts.


Hide 36100 2.SECURE TRANSFER ASSEMBLY

C278909C01
0.188,0.094 0.5,0.292 0.313,0.198 10 *A 0.219,2.625 0.531,2.823 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


a.

Secure the transfer assembly to the overhaul attachment.


Hide 36111G 3.REMOVE TRANSFER CASE STRAIGHT PIN

C278910C01
0.167,0.24 0.479,0.438 0.313,0.198 10 *A 0.177,2.521 0.49,2.719 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


a.

Remove the 2 transfer case straight pins.


Hide 36114B 4.REMOVE NO. 1 TRANSFER CASE PLUG

C130044

a.

Remove the No. 1 transfer case plug and gasket.


Hide 36114F 5.REMOVE TRANSFER DRAIN PLUG

C278911C01
0.063,0.052 0.375,0.25 0.313,0.198 10 *A 0.094,2.479 0.406,2.677 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


a.

Using a 10 mm socket hexagon wrench, remove the transfer drain plug and gasket.


Hide 36114H 6.REMOVE NO. 2 TRANSFER CASE PLUG

C278912C01
0.125,0.104 0.438,0.302 0.313,0.198 10 *A 0.125,2.563 0.438,2.76 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


a.

Using a 10 mm socket hexagon wrench, remove the No. 2 transfer case plug (filler plug) and gasket.


Hide 36111H 7.REMOVE TRANSFER CASE BREATHER PLUG

C222931

a.

Using a chisel and hammer, slightly pry out the transfer case breather plug.


b.

Using a screwdriver, lightly pry up and remove the transfer case breather plug.


Hide 36111B 8.REMOVE TRANSFER CASE OIL SEAL

C278959C01
0.583,0.885 0.75,0.885 0.75,0.885 1.083,0.552 true 0.573,3.021 0.74,3.021 0.74,3.021 1.073,2.688 true 2.083,1.917 2.25,1.917 2.25,1.917 2.333,1.417 true 2.052,4.063 2.219,4.063 2.219,4.063 2.302,3.563 true 0.438,0.813 0.75,1.01 0.313,0.198 10 false *1 0.427,2.938 0.74,3.135 0.313,0.198 10 false *1 1.771,3.99 2.083,4.188 0.313,0.198 10 false SST 1.802,1.844 2.115,2.042 0.313,0.198 10 false SST 0.052,0.063 0.365,0.26 0.313,0.198 10 false *A 0.063,2.229 0.375,2.427 0.313,0.198 10 false *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F
*1 Transfer Case Oil Seal


a.

Using SST, remove the transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal.



Hide 36113A 9.REMOVE TRANSFER CASE OIL SEAL RH

C130055C03
1.875,1.188 1.75,1.802 1.75,1.802 1.615,1.802 false 0.771,0.354 0.583,0.625 0.583,0.625 0.438,0.625 true 1.323,1.729 1.729,1.948 0.406,0.219 10 SST 0.281,0.542 0.635,0.76 0.354,0.219 10 *1
*1 Transfer Case Oil Seal RH


a.

Using SST, remove the transfer case oil seal RH from the No. 1 transfer case cover.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal RH.



Hide 10.INSPECT TOTAL PRELOAD

C130167C02
2.417,0.667 2.031,0.667 false 2.469,0.594 2.781,0.75 0.313,0.156 10 *1 0.167,0.177 0.625,0.375 0.458,0.198 10 90°
*1 Nut


a.

Install nuts to the stud bolts.

HINT:

Use nuts that are used for installing the propeller shaft.



b.

Using a torque wrench, check the total preload (starting torque) with the teeth of the drive pinion and ring gear in contact.

Torque:
Total preload (starting torque) : 0.87 to 2.85 N*m (8.88 to 29.06 kgf*cm, 7.71 to 25.22 in.*lbf)

HINT:

Install the torque wrench as shown in the illustration.



Hide 11.INSPECT RING GEAR BACKLASH

C158062

a.

Insert a dial indicator through the No. 2 transfer case plug hole, and set it perpendicular to the edge of a ring gear tooth.

If the backlash is not within the specified range, adjust the backlash or repair as necessary.


b.

While securing the transfer output shaft by hand, rotate the transfer ring gear mounting case forward and backward by hand and measure the backlash of the ring gear and driven pinion.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


NOTICE:

Measure the ring gear at 3 or more locations.



Hide 36121 12.REMOVE NO. 1 TRANSFER CASE COVER

a.
C130048

Remove the 8 bolts.


b.
C130049

Using a brass bar and hammer, remove the No. 1 transfer case cover from the transfer case.

NOTICE:
·

Put the brass bar against the rib of the No. 1 transfer case cover.

·

When removing the No. 1 transfer case cover, be careful not to scratch the installation surface.



HINT:

To prevent the No. 1 transfer case cover from falling, leave 2 of the bolts screwed in by 5 or 6 threads.



Hide 41201P 13.REMOVE TRANSFER RING GEAR

C130050

a.

Remove the transfer ring gear from the transfer case.


Hide 36111G 14.REMOVE TRANSFER CASE STRAIGHT PIN

C130051

a.

Remove the 2 transfer case straight pins from the transfer case.


Hide 15.INSPECT DRIVEN PINION PRELOAD

a.
C130052C02
2.479,0.656 2.031,0.656 false 2.531,0.583 2.844,0.74 0.313,0.156 10 *1 0.146,0.115 0.458,0.271 0.313,0.156 10 90°
*1 Nut


Install nuts to the stud bolts.

HINT:

Use nuts that are used for installing the propeller shaft.



b.

Using a torque wrench, check the driven pinion preload (starting torque) of the driven pinion.

Torque:
Driven pinion preload (starting torque) : 0.39 to 2.21 N*m (3.98 to 22.53 kgf*cm, 3.46 to 19.55 in.*lbf)

HINT:

Install the torque wrench as shown in the illustration.



Hide 36202 16.REMOVE REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

C130053

a.

Remove the 5 bolts and rear transfer output shaft sub-assembly from the transfer case.


b.

Mount the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C130056N07
1.094,1.094 1.219,1.094 1.219,1.094 1.406,0.896 false 0.802,1.042 1.26,1.24 0.458,0.198 10 SST

Using SST and a hammer, unstake the transfer gear nut.

SST
09930-00010  

NOTICE:
·

Be sure to use SST with the tapered surface facing the shaft.

·

Do not grind the tip of SST with a grinder or other device.

·

Completely loosen the staked part of the transfer gear nut when removing it.

·

Do not damage the threads of the output shaft sub-assembly.




d.

Using a 30 mm socket wrench, remove the transfer gear nut.


Hide 41201P 17.REMOVE TRANSFER DRIVEN PINION

a.
C109627N10
2.313,0.479 2.458,0.479 2.458,0.479 2.76,0.844 true 2.74,1.01 2.458,0.479 true 2.51,1.052 2.448,0.479 true 1.917,0.448 2.26,0.615 0.344,0.167 10 SST

w/o Washer:

i.

Using SST and a press, remove the transfer driven pinion from the rear transfer output shaft sub-assembly.

SST
09950-00020  
09950-60010  (09951-00240)
09950-70010  (09951-07100)

NOTICE:

Support the front transfer driven pinion bearing as shown in the illustration to avoid placing stress on the outer race.




b.
C109627N10
2.313,0.479 2.458,0.479 2.458,0.479 2.76,0.844 true 2.74,1.01 2.458,0.479 true 2.51,1.052 2.448,0.479 true 1.917,0.448 2.26,0.615 0.344,0.167 10 SST

w/ Washer:

i.

Using SST and a press, remove the transfer driven pinion and washer from the rear transfer output shaft sub-assembly.

SST
09950-00020  
09950-60010  (09951-00240)
09950-70010  (09951-07100)

NOTICE:

Support the front transfer driven pinion bearing as shown in the illustration to avoid placing stress on the outer race.




Hide 33325A 18.REMOVE REAR TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C109629N10
2.365,0.563 2.25,0.563 2.25,0.563 2,1.021 false 2.406,0.49 2.729,0.667 0.323,0.177 10 SST

Using SST and a press, remove the rear transfer output shaft dust deflector from the rear transfer output shaft sub-assembly.

SST
09950-00020  


Hide 41201K 19.REMOVE FRONT TRANSFER DRIVEN PINION BEARING

C109628N10
1.859,0.496 2.2,0.661 0.341,0.166 10 SST 2.26,0.599 2.724,0.599 false 2.26,0.599 2.595,1.064 false 2.26,0.599 2.326,1.035 false

a.

Using SST and a press, remove the front transfer driven pinion bearing from the transfer driven pinion.

SST
09950-00020  
09950-60010  (09951-00410)
09950-70010  (09951-07100)

NOTICE:

Support the front transfer driven pinion bearing as shown in the illustration to avoid placing stress on the outer race.



b.
C109630

Remove the O-ring from the front transfer driven pinion bearing.


Hide 33309H 20.REMOVE TRANSFER OUTPUT SHAFT WASHER

C110759

a.

Remove the transfer output shaft washer from the transfer driven pinion.


Hide 41301H 21.REMOVE RING GEAR MOUNTING CASE BEARING RH

C269126C02
2.563,1.51 2.844,1.896 true 2.365,1.563 2.844,1.896 2.844,1.896 3.031,1.896 true 3.052,0.5 3.365,0.656 0.313,0.156 10 *a 1.531,1.021 1.844,1.177 0.313,0.156 10 *b 3.083,1.781 3.427,1.979 0.344,0.198 10 SST
*a Turn
*b Hold


a.

Using SST, remove the ring gear mounting case bearing RH (inner race) from the transfer ring gear mounting case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00540)

NOTICE:
·

Apply a lubricant to the threads and end of SST.

·

Do not deform the cage of the ring gear mounting case bearing RH (inner race) (when reusing the bearing).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the bearings).




b.
C156143C03
2.156,0.979 2.531,0.979 false 0.573,0.688 0.573,1.469 0.573,1.469 0.854,1.469 true 0.927,1.198 0.75,1.198 0.75,1.198 0.75,0.594 true 0.958,1.104 1.229,1.281 0.271,0.177 10 *1 0.896,1.385 1.167,1.542 0.271,0.156 10 *2 2.552,0.906 3.063,1.219 0.51,0.313 10 SST
*1 No. 2 Transfer Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing RH (Outer Race)


Using SST and a hammer, remove the No. 2 transfer ring gear mounting case washer and ring gear mounting case bearing RH (outer race) from the No. 1 transfer case cover.

SST
09310-35010  


Hide 41301H 22.REMOVE RING GEAR MOUNTING CASE BEARING LH

C269127C02
0.583,1.729 0.719,1.729 0.719,1.729 0.969,1.552 true 1.042,1.167 0.698,1.729 true 0.229,1.625 0.688,1.823 0.458,0.198 10 SST 2.76,0.271 3.073,0.427 0.313,0.156 10 *a 0.365,0.76 0.677,0.917 0.313,0.156 10 *b
*a Turn
*b Hold


a.

Using SST, remove the ring gear mounting case bearing LH (inner race) from the transfer ring gear mounting case.

SST
09950-00020  
09950-00030  

NOTICE:
·

Apply a lubricant to the threads and end of SST.

·

Do not deform the cage of the ring gear mounting case bearing LH (inner race) (when reusing the bearing).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the bearings).




b.
C277127C01
1.323,1.688 1.156,1.688 1.156,1.688 1.156,1.146 true 0.469,1.24 0.469,2.073 0.469,2.073 0.719,2.073 true 2.031,1.177 2.604,2.198 2.604,2.198 2.781,2.198 true 2,3.531 2.635,4.344 2.635,4.344 2.854,4.344 true 1.167,3.458 1.167,4.5 1.167,4.5 1.323,4.5 true 0.49,3.531 0.49,4.302 0.49,4.302 0.667,4.302 true 0.073,0.021 0.385,0.219 0.313,0.198 10 false *A 0.115,2.448 0.427,2.646 0.313,0.198 10 false *B 1.385,1.615 1.698,1.813 0.313,0.198 10 false *1 0.771,1.979 1.083,2.177 0.313,0.198 10 false *2 2.823,2.115 3.281,2.313 0.458,0.198 10 false SST 2.885,4.271 3.344,4.469 0.458,0.198 10 false SST 1.385,4.406 1.698,4.604 0.313,0.198 10 false *1 0.719,4.208 1.031,4.406 0.313,0.198 10 false *2
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F
*1 No. 1 Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing LH (Outer Race)


Using SST and a hammer, remove the No. 1 ring gear mounting case washer and ring gear mounting case bearing LH (outer race) from the transfer case.

SST
09636-20010  


Hide 36212L 23.REMOVE SHAFT SNAP RING

C109636

a.

Using a snap ring expander, remove the shaft snap ring.


Hide 41319 24.REMOVE TRANSFER RING GEAR MOUNTING CASE

C109637N10
1.906,0.406 2.115,0.406 false 2.135,0.333 2.615,0.563 0.479,0.229 10 SST

a.

Using SST and a press, remove the transfer ring gear mounting case from the transfer ring gear.

SST
09950-60010  (09951-00400)


Hide 36128B 25.REMOVE BREATHER OIL DEFLECTOR

C277128C01
0.083,0.073 0.396,0.271 0.313,0.198 10 *A 0.073,2.406 0.385,2.604 0.313,0.198 10 *B
*A for K111F
*B for U660F, U760F, EA64F, EB61F, EB63F, K114F


a.

Remove the 2 bolts and breather oil deflector from the transfer case.