*1: for Radio and Display Type
*2: for Navigation Receiver Type
The combination meter assembly communicates with the ECM via the CAN communication system.
The combination meter assembly communicates with the brake actuator assembly (skid control ECU) via the CAN communication system.
The combination meter assembly communicates with the power steering ECU assembly via the CAN communication system.
The combination meter assembly communicates with the main body ECU (multiplex network body ECU) via the CAN communication system.
The combination meter assembly communicates with the airbag sensor assembly via the CAN communication system.
The combination meter assembly communicates with the radio and display receiver assembly*1 or navigation receiver assembly*2 via the CAN communication system.
The combination meter assembly communicates with the Driving support ECU assembly via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the ECM continues for 2 seconds or more. |
·
ECM ·
CAN communication system ·
Combination meter assembly |
| U0129 | Lost Communication with Skid Control ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the brake actuator assembly (skid control ECU) continues for 3 seconds or more. |
·
Brake actuator assembly (skid control ECU) ·
CAN communication system ·
Combination meter assembly |
| U0131 | Lost Communication with Electric Power Steering ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the power steering ECU assembly continues for 3 seconds or more. |
·
Power steering ECU assembly ·
CAN communication system ·
Combination meter assembly |
| U0142 | Lost Communication with Main Body ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the main body ECU (multiplex network body ECU) continues for 3 seconds or more. |
·
Main body ECU (Multiplex network body ECU) ·
CAN communication system ·
Combination meter assembly |
| U0151 | Lost Communication with Airbag ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the airbag sensor assembly continues for 10 seconds or more. |
·
Airbag sensor assembly ·
CAN communication system ·
Combination meter assembly |
| U0163 | Last Communication With Navigation ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the Navigation ECU continues for 3 seconds or more. |
·
Radio and display receiver assembly*1 or navigation receiver assembly*2 ·
CAN communication system ·
Combination meter assembly |
| U023A | Lost Communication with Front Camera Module | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the front camera module continues for 10 seconds or more. |
·
Forward recognition camera ·
CAN communication system ·
Combination meter assembly |
| U1104 | Lost Communication with Driving Support ECU | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
No communication with the front driving support ECU continues for 10 seconds or more. |
·
Driving support ECU ·
CAN communication system ·
Combination meter assembly |
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
If CAN communication system DTC U0100, U0129, U0131, U0142, U0151, U0163, U023A or U1104 and another DTC are output at the same time, perform troubleshooting for CAN communication system DTC U0100, U0129, U0131, U0142, U0151, U0163, U023A or U1104 first.
| Proceed to |
|---|
| CAN communication system DTC is not output |
| CAN communication system DTC is output |
CAN communication system DTC is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication system DTC is output
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING