The ECM stores DTC P1589 if the ECM or other components that require the yaw rate and acceleration sensor (airbag sensor assembly) to be calibrated (deceleration sensor zero point calibration) are replaced and calibration is terminated or the vehicle is driven before calibration is complete.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1589 | Acceleration Sensor Learning Value | Condition 1:
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other 1.
The vehicle speed is 2 km/h (1.2 mph) or more. 2.
Deceleration sensor zero point calibration has not been completed. 3.
- 4.
1 trip detection logic Condition 2: 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other 1.
Deceleration sensor zero point calibration is performed. 2.
The learned values of the deceleration sensor zero point calibration are abnormal (out of normal range). 3.
- 4.
1 trip detection logic |
Condition 1:
Deceleration sensor zero point calibration has not been performed Condition 2: ·
Vehicle was not stabilized during the deceleration sensor zero point calibration ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
ECM |
- | DTC stored |
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If the CVT oil pressure calibration is performed before the deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform the steps below to return the system to normal.
Always perform zero point calibration with the vehicle on level ground (Inclination: 0 +/-0.25°).
Do not shake or vibrate the vehicle during zero point calibration.
Turn the ignition switch off.
Move the shift lever to P and apply the parking brake.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
| Tester Display |
|---|
| Reset Memory |
Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor Zero Point Calibration.
| Tester Display |
|---|
| Deceleration Sensor Zero Point Calibration |
When "Complete" is displayed on the screen, the deceleration sensor zero point calibration is completed.
If "Error" is displayed on the screen and DTC P1589 is output (confirm the DTC detection conditions), the yaw rate and acceleration sensor (airbag sensor assembly) circuit may have a malfunction.
Shaking or vibrating the vehicle during zero point calibration may cancel calibration. If "Error" is displayed on the screen and DTC P1589 is not output, perform calibration again.
| Result | Proceed to |
|---|---|
| Deceleration sensor zero point calibration is completed normally | A |
| DTC P1589 is output | B |
A
B
Do not initialize the learned values by performing reset memory.
Turn the ignition switch off and wait at least 30 seconds.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait at least 2 seconds.
Do not start the engine.
CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, the calibration cannot be performed under the following conditions:
Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or higher.
CVT oil temperature is -5°C (23°F) or less or 100°C (212°F) or higher.
Turn the GTS on.
Start the engine and wait at least 5 seconds.
Start the engine with the shift lever in P.
After starting the engine, do not operate the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.
| Tester Display |
|---|
| CVT Oil Pressure Calibration |
During CVT oil pressure calibration, the engine idle speed will increase.
When "Complete" is displayed on the screen, the CVT oil pressure calibration is completed.
The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.
Check that no DTC is stored.
| Proceed to |
|---|
| NEXT |
NEXT
Check the yaw rate and acceleration sensor (airbag sensor assembly) for any inclination, bracket deformation or installation clearance.
The yaw rate and acceleration sensor (airbag sensor assembly) is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| G Sensor |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of deceleration sensor | min.: 0 V
max.: 79.998 V |
Displays converted voltage of deceleration sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is as specified under Normal Condition |
| Data displayed is not as specified under Normal Condition |
Data displayed is as specified under Normal Condition
Data displayed is not as specified under Normal Condition
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT