The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.
The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft speed and sends it to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0720 | Output Speed Sensor Circuit | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
A transmission revolution (NOUT) signal malfunction is not detected. 2.
The transmission revolution sensor (NOUT) output voltage is less than 0.1 V, or higher than 1.9 V. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NOUT) circuit ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored |
| P0722 | Output Speed Sensor Circuit No Signal | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch. 2.
The speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NOUT) circuit ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored |
| P077C | Output Speed Sensor Circuit Low | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
A transmission revolution (NOUT) signal malfunction is not detected. 2.
The transmission revolution sensor (NOUT) output voltage is less than 0.1 V. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NOUT) circuit ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored |
| P077D | Output Speed Sensor Circuit High | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
A transmission revolution (NOUT) signal malfunction is not detected. 2.
The transmission revolution sensor (NOUT) output voltage is higher than 1.9 V. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NOUT) circuit ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored |
The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.
If the ECM detects no signal from the secondary pulley speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the secondary pulley speed sensor. The ECM will illuminate the MIL and store the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| SPD (NOUT) |
| NOUT Sensor Voltage |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NOUT) | Secondary pulley speed (NOUT) | min.: 0 rpm
max.: 12750 rpm |
·
Vehicle stopped: 0 rpm ·
Vehicle cruising at approx. 60 km/h (37 mph): 2850 rpm |
Data is displayed in increments of 50 rpm. |
| NOUT Sensor Voltage | Secondary pulley speed (NOUT) sensor output voltage | min.: 0.000 V
max.: 4.999 V |
Engine idling: Approx. 2 V | - |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
Remove the transmission revolution sensor (NOUT).
Click hereDrivetrain>K111F MULTIDRIVE / CVT>REVOLUTION SENSOR>REMOVAL
| *1 | Transmission Revolution Sensor (NOUT) | *2 | Ammeter |
| *3 | Battery | - | - |
| *a | 5 mm (0.197 in.) Gap or Closer | - | - |
Connect the battery to the sensor as shown in the illustration.
Wave a magnetic object left and right in front of the transmission revolution sensor tip (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.
Make sure to wave the magnetic object during the inspection. Current will not change without waving the magnetic object as indicated by the arrow in the illustration.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NOTO) - 2 (NOTB) | Low signal | 4 to 8 mA |
| 1 (NOTO) - 2 (NOTB) | High signal | 12 to 16 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B31 transmission revolution sensor (NOUT) connector.
Disconnect the B75 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B31-1 (NOTO) - B75-129 (NOTO) | Always | Below 1 Ω |
| B31-2 (NOTB) - B75-130 (NOTB) | Always | Below 1 Ω |
| B31-1 (NOTO) or B75-129 (NOTO) - Body ground | Always | 10 kΩ or higher |
| B31-2 (NOTB) or B75-130 (NOTB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT