Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P014C  A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D  A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P015A  A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B  A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  


DESCRIPTION

HINT:

Refer to DTC P2195.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P2195


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P014C A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored
P014D A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored
P015A A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 The "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored
P015B A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 The "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored

*: Calculated by ECM based on the air fuel ratio sensor output.

MONITOR DESCRIPTION

After the engine has been warmed up, the ECM carries out air fuel ratio feedback control, and maintains the air fuel ratio at the theoretical level. In addition, after all the preconditions have been met, active air fuel ratio control is carried out for approximately 10 seconds and during active air fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing a specific injection quantity based on the theoretical air fuel ratio learned during normal air fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air fuel ratio control.

If the air fuel ratio sensor's response ability is reduced, DTC P014C and P014D are output.

If the air fuel ratio sensor output timing is delayed, DTC P015A and P015B are output.

A223538E33
4.24,1.74 4.052,1.385 false 5.229,1.979 5.448,1.354 false 4.188,3 4.042,2.802 false 4.438,3 4.771,2.604 false 0.135,0.031 2.417,0.219 2.281,0.188 10 Air Fuel Ratio Sensor Output: 0.292,0.979 1.729,1.365 1.438,0.385 10 Active Air Fuel Ratio Control 0.292,1.938 2.135,2.281 1.844,0.344 10 Air Fuel Ratio Sensor Output (Response Rate) 3.563,1.313 4.063,1.5 0.5,0.188 10 Normal 5.479,1.281 6.24,1.469 0.76,0.188 10 Malfunction 4.438,0.458 5.25,0.646 0.813,0.188 10 10 seconds 0.292,4.25 1.698,4.438 1.406,0.188 10 Fuel Injection Volume 2.771,3.969 3.417,4.156 0.646,0.188 10 Increase 2.771,4.438 3.417,4.625 0.646,0.188 10 Decrease 1.833,0.771 2.229,0.917 0.396,0.146 10 On 1.833,1.073 2.208,1.26 0.375,0.188 10 Off 0.292,3.125 2.146,3.479 1.854,0.354 10 Air Fuel Ratio Sensor Output (Delay Time) 3.583,2.688 4.083,2.875 0.5,0.188 10 Normal 4.792,2.542 5.552,2.729 0.76,0.188 10 Malfunction

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions are met -
Engine coolant temperature 75°C (167°F) or higher
Idle Off
Engine speed 1200 rpm or higher, and less than 2500 rpm
Air fuel ratio sensor status Activated
Engine load 10% or higher, and less than 75%
Shift position 2nd or more
Catalyst monitor Not yet
Mass air flow 10 gm/sec or more, and less than 40 gm/sec

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation pattern will activate the air fuel ratio sensor response monitor.


A201252E80
0.677,0.406 1.719,0.938 1.042,0.531 10 Vehicle Speed 0.021,0.938 1.677,1.292 1.656,0.354 10 Between 75 and 100 km/h 1.219,2.323 1.667,2.688 0.448,0.365 10 Idling 0.458,2.604 1.74,2.99 1.281,0.385 10 Engine Switch off 2.354,2.177 2.552,2.365 0.198,0.188 10 [A] 3.906,0.792 4.115,0.969 0.208,0.177 10 [B] 2.073,2.906 3.052,3.188 0.979,0.281 10 Warming up 3.573,2.938 4.542,3.313 0.969,0.375 10 10 minutes 5.708,2.781 6.156,3.115 0.448,0.333 10 Time 4.656,3.042 4.854,3.229 0.198,0.188 10 [C]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) and turn the GTS on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

8.

Check that O2 Sensor / Current is Incomplete.

HINT:

The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1 and LR DELAY B1S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated in each test item).


9.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].

10.

Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Check that O2 Sensor / Current becomes Complete.

HINT:

Check the test values on the GTS by entering the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1 and LR DELAY B1S1.


12.

If the monitor item O2 Sensor / Current does not become Complete (if the test values indicated on the GTS do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>READINESS MONITOR DRIVE PATTERN

13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

16.

Input the DTC: P014C, P014D, P015A or P015B.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P014C, P014D, P015A or P015B is output A
DTC P014C, P014D, P015A or P015B and other DTCs are output B


HINT:

If any DTCs other than P014C, P014D, P015A or P015B are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P0031

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

4.INSPECT AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR FUEL RATIO SENSOR
a.

Check that the proper air fuel ratio sensors are installed to the vehicle.

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P014C, P014D, P015A or P015B are output A
DTC is not output B




A

7.REPLACE AIR FUEL RATIO SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P014C, P014D, P015A or P015B are output B




A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO