Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047053 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

The illumination of the low beam headlights is controlled by the main body ECU (multiplex network body ECU). When the headlights are turned on, the main body ECU (multiplex network body ECU) receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2430 LED Headlight LH Circuit Malfunction LED headlight LH circuit malfunction
·

Headlight unit LH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


B2431 LED Headlight RH Circuit Malfunction LED headlight RH circuit malfunction
·

Headlight unit RH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



HINT:

DTC B2430 and B2431 are not output if 20 seconds have not elapsed since the ignition switch was turned on.


WIRING DIAGRAM

E341415E01
2.677,0.354 4.51,0.552 1.833,0.198 10 false from Battery 1.281,0.521 3.115,0.719 1.833,0.198 10 false H-LP-MAIN 1.292,1.198 1.51,1.427 0.219,0.229 10 false 1 2.094,1.198 2.313,1.427 0.219,0.229 10 false 2 1.302,1.646 1.521,1.875 0.219,0.229 10 false 5 2.083,1.646 2.302,1.875 0.219,0.229 10 false 3 1.583,2.063 3.417,2.26 1.833,0.198 10 false H-LP 0.531,3.948 0.719,4.146 0.188,0.198 10 false 2 0.802,4.052 0.99,4.25 0.188,0.198 10 false E 2.573,3.771 2.938,3.969 0.365,0.198 10 false LO 2.844,3.646 3.208,3.844 0.365,0.198 10 false 1 2.635,4.302 2.823,4.5 0.188,0.198 10 false B 2.865,4.229 3.052,4.427 0.188,0.198 10 false 3 3.188,3.927 4.146,4.094 0.958,0.167 10 false H-LP LH-LO 0.781,6.469 0.969,6.667 0.188,0.198 10 false E 0.854,4.865 1.385,5.063 0.531,0.198 10 false A78 0.542,6.333 0.729,6.531 0.188,0.198 10 false 2 2.615,6.76 2.802,6.958 0.188,0.198 10 false B 2.875,6.635 3.063,6.833 0.188,0.198 10 false 3 2.51,6.198 2.875,6.396 0.365,0.198 10 false LO 2.875,6.115 3.24,6.313 0.365,0.198 10 false 1 3.281,6.385 4.24,6.552 0.958,0.167 10 false H-LP RH-LO 0.854,5.021 4.146,5.208 3.292,0.188 10 false Headlight Unit LH 0.896,7.281 1.427,7.479 0.531,0.198 10 false A79 0.906,7.469 4.198,7.656 3.292,0.188 10 false Headlight Unit RH 5.51,1.333 5.698,1.5 0.188,0.167 10 false A 5.479,1.115 5.667,1.281 0.188,0.167 10 false 15 5.833,1.323 6.344,1.5 0.51,0.177 10 false HRLY 3.146,1.219 3.521,1.385 0.375,0.167 10 false 37 3.438,1.906 3.813,2.073 0.375,0.167 10 false 3B 3.458,2.063 5.115,2.438 1.656,0.375 10 false Instrument Panel Junction Block Assembly 5.406,4.344 5.729,4.5 0.323,0.156 10 false G79 5.406,6.771 5.729,6.927 0.323,0.156 10 false G79 5.438,4.115 5.76,4.271 0.323,0.156 10 false 24 5.823,4.344 6.417,4.552 0.594,0.208 10 false LLEW 5.438,6.531 5.76,6.688 0.323,0.156 10 false 21 5.823,6.792 6.594,6.99 0.771,0.198 10 false RLEW 5.385,7.729 7.031,8.083 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>PRECAUTION



PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B2430 or B2431 output does not occur.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT HEADLIGHT RELAY (H-LP)
3.INSPECT HEADLIGHT RELAY (H-LP)
a.

Remove the headlight relay from the No. 1 engine room relayblock.


b.

Inspect the head light relay.

Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)
a.
E341416C01
0.083,0.063 0.396,0.219 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Headlight Relay)


Remove the headlight relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 1 - Body ground Always 11 to 14 V
Headlight relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay from the No. 1 engine room relay block.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - 3B-37 Always Below 1 Ω
3B-37 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E338830N01
1.51,2.26 1.906,2.521 0.396,0.26 1.479,0.281 1.875,0.542 0.396,0.26 1.615,3.063 1.615,2.813 false 1.594,0.323 1.906,0.521 0.313,0.198 10 false 3B 1.656,2.292 1.969,2.49 0.313,0.198 10 false A 1.438,3.094 2.052,3.292 0.615,0.198 10 false HRLY

for LHD:

i.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


ii.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL



b.

for RHD:

i.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


ii.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-15 (HRLY) - 3B-37 Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT UNIT)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - HEADLIGHT UNIT)
a.

Remove the headlight relay from the No. 1 engine room relay block.


b.

Disconnect the A78*1 and A79*2 headlight unit connectors.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
Headlight relay terminal 3 - A78-1 (LO) Always Below 1 Ω
Headlight relay terminal 3 - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
Headlight relay terminal 3 - A79-1 (LO) Always Below 1 Ω
Headlight relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the A78*1 or A79*2 headlight unit connector.

*1: for LH

*2: for RH



b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
A78-3 (B) - G79-24 (LLEW) Always Below 1 Ω
A78-2 (E) - Body ground Always Below 1 Ω
A78-3 (B) - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
A79-3 (B) - G79-21 (RLEW) Always Below 1 Ω
A79-2 (E) - Body ground Always Below 1 Ω
A79-3 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HEADLIGHT UNIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT UNIT
a.

Temporarily replace the headlight unit with a new or normally functioning one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B2430 or B2431 output does not occur.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (HEADLIGHT UNIT WAS DEFECTIVE)

B

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)