Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047053 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight (HI-BEAM) Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals and illuminates the high beam headlights.

WIRING DIAGRAM

E333805E03
0.094,0.063 1.875,0.375 1.781,0.313 12 false for Halogen Headlight: 2.469,1.771 3.125,1.99 0.656,0.219 10 false DIMMER 3.167,0.917 3.323,1.115 0.156,0.198 10 false 1 3.167,1.313 3.323,1.51 0.156,0.198 10 false 5 2.281,0.927 2.438,1.125 0.156,0.198 10 false 2 2.26,1.313 2.417,1.51 0.156,0.198 10 false 3 1.01,1.24 1.802,1.5 0.792,0.26 10 false H-LP-MAIN 1.219,0.552 2.063,0.771 0.844,0.219 10 false from Battery 4.125,1.823 5.729,2.208 1.604,0.385 10 false Instrument Panel Junction Block Assembly 4.125,1.667 4.438,1.865 0.313,0.198 10 false 3B 5.365,4.177 7.031,4.542 1.667,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.365,4.021 5.521,4.219 0.156,0.198 10 false A 6.052,1.031 6.51,1.229 0.458,0.198 10 false DIM 3.917,0.906 4.229,1.104 0.313,0.198 10 false 54 1.167,4.344 2.365,4.542 1.198,0.198 10 false Headlight Unit LH 1.177,4.177 1.635,4.375 0.458,0.198 10 false A83 2.594,3.365 2.75,3.563 0.156,0.198 10 false B 2.563,5.188 2.719,5.385 0.156,0.198 10 false B 0.854,3.385 1.01,3.583 0.156,0.198 10 false E 0.854,5.177 1.01,5.375 0.156,0.198 10 false E 2.823,3.375 2.979,3.573 0.156,0.198 10 false 2 0.635,3.396 0.792,3.594 0.156,0.198 10 false 1 2.833,5.177 2.99,5.375 0.156,0.198 10 false 2 0.646,5.167 0.802,5.365 0.156,0.198 10 false 1 1.229,6 1.688,6.198 0.458,0.198 10 false A85 1.229,6.177 2.427,6.375 1.198,0.198 10 false Headlight Unit RH 5.76,0.927 6.073,1.125 0.313,0.198 10 false 22 3.271,3.708 4.063,3.938 0.792,0.229 10 false H-LP LH-HI 3.333,5.521 4.125,5.75 0.792,0.229 10 false H-LP RH-HI

E333806E04
1.24,4.375 2.396,4.573 1.156,0.198 10 false Headlight Unit LH 1.25,4.219 1.708,4.417 0.458,0.198 10 false A78 1.25,6 1.708,6.198 0.458,0.198 10 false A79 1.25,6.177 2.406,6.375 1.156,0.198 10 false Headlight Unit RH 2.833,3.385 2.99,3.583 0.156,0.198 10 false 4 2.833,5.188 2.99,5.385 0.156,0.198 10 false 4 2.604,3.385 2.76,3.583 0.156,0.198 10 false B 2.615,5.188 2.771,5.385 0.156,0.198 10 false B 0.865,3.406 1.021,3.604 0.156,0.198 10 false E 0.646,3.396 0.802,3.594 0.156,0.198 10 false 5 0.854,5.188 1.01,5.385 0.156,0.198 10 false E 0.635,5.198 0.792,5.396 0.156,0.198 10 false 5 2.49,1.76 3.115,1.979 0.625,0.219 10 false DIMMER 1.031,1.24 1.792,1.479 0.76,0.24 10 false H-LP-MAIN 1.229,0.563 2.104,0.802 0.875,0.24 10 false from Battery 4.146,1.833 5.75,2.198 1.604,0.365 10 false Instrument Panel Junction Block Assembly 4.146,1.667 4.458,1.865 0.313,0.198 10 false 3B 3.948,0.896 4.26,1.094 0.313,0.198 10 false 54 5.75,0.906 6.063,1.104 0.313,0.198 10 false 22 6.063,1.031 6.521,1.229 0.458,0.198 10 false DIM 5.438,4.083 7.104,4.438 1.667,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.438,3.896 5.594,4.094 0.156,0.198 10 false A 3.167,0.906 3.323,1.104 0.156,0.198 10 false 1 2.25,0.917 2.406,1.115 0.156,0.198 10 false 2 3.177,1.281 3.333,1.479 0.156,0.198 10 false 5 2.26,1.302 2.417,1.5 0.156,0.198 10 false 3 0.125,0.073 1.771,0.365 1.646,0.292 12 false for LED Headlight: 3.313,3.677 4.135,3.917 0.823,0.24 10 false H-LP LH-HI 3.323,5.51 4.146,5.75 0.823,0.24 10 false H-LP RH-HI

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the bulbs and fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEADLIGHT)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Head Light Hi Headlight dimmer relay ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Head Light Hi
50004 123 15

Result:
Proceed to
High beam headlights come on
High beam headlights do not come on



High beam headlights come on

High beam headlights do not come on

2.INSPECT HEADLIGHT DIMMER RELAY (DIMMER)
2.INSPECT HEADLIGHT DIMMER RELAY (DIMMER)
a.
E270112N01
2.813,1.073 3.104,1.073 false 1.865,1.073 2.052,1.073 false 2.458,1.615 2.458,1.417 false 2.469,0.698 2.573,0.438 false 0.458,1.26 0.615,1.458 0.156,0.198 10 1 2.594,0.323 2.75,0.521 0.156,0.198 10 1 1.271,1.25 1.427,1.448 0.156,0.198 10 2 2.438,1.656 2.594,1.854 0.156,0.198 10 2 1.26,0.833 1.469,1.042 0.208,0.208 10 2 1.271,0.698 1.479,0.906 0.208,0.208 10 3 0.469,0.698 0.677,0.906 0.208,0.208 10 5 1.708,1 1.917,1.208 0.208,0.208 10 3 3.167,0.99 3.375,1.198 0.208,0.208 10 5

Remove the headlight dimmer relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - BATTERY)

NG

REPLACE HEADLIGHT DIMMER RELAY (DIMMER)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - BATTERY)
a.
E333879C02
0.052,0.042 0.365,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Headlight Dimmer Relay)


Remove the headlight dimmer relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight dimmer relay terminal 3 - Body ground Always 11 to 14 V
Headlight dimmer relay terminal 2 - Body ground



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight dimmer relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight dimmer relay terminal 1 - 3B-54 Always Below 1 Ω
3B-54 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E338830E06
1.51,2.26 1.906,2.521 0.396,0.26 1.479,0.281 1.875,0.542 0.396,0.26 2.167,3.063 2.167,2.813 false 1.594,0.323 1.906,0.521 0.313,0.198 10 false 3B 1.656,2.292 1.969,2.49 0.313,0.198 10 false A 2.042,3.104 2.656,3.302 0.615,0.198 10 false DIM

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-22 (DIM) - 3B-54 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG