Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM J

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The TCM memory contains the programs for the normal and sport shift patterns.

By following the programs corresponding to the signals from the combination switch assembly, park/neutral position switch and other various sensors, the TCM switches the shift solenoid valves on and off, and controls the transaxle gear ratio.

WIRING DIAGRAM

C279696E01
2.594,2.01 4.01,2.25 1.417,0.24 10 Combination Switch 2.583,1.813 3.042,2.01 0.458,0.198 10 G60 5.604,1.219 6.219,1.417 0.615,0.198 10 PWMS 5.344,1.333 5.802,1.531 0.458,0.198 10 36 3.917,1.333 4.375,1.531 0.458,0.198 10 2 2.365,1.333 2.823,1.531 0.458,0.198 10 4 3.396,1.104 4.01,1.302 0.615,0.198 10 MSW1 2.552,1.104 3.167,1.302 0.615,0.198 10 MSW2 5.823,3.885 6.438,4.083 0.615,0.198 10 A61 5.823,4.063 6.438,4.26 0.615,0.198 10 ECM 3.042,3.688 3.656,3.885 0.615,0.198 10 TCM 0.406,4.438 4.073,4.635 3.667,0.198 10 : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.



PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C277027C01
1.292,1.729 1.5,1.385 true 2.104,1.729 1.865,1.385 true 1.073,1.781 1.688,1.979 0.615,0.198 10 false MSW2 1.938,1.781 2.552,1.979 0.615,0.198 10 false MSW1 0.104,0.104 0.719,0.302 0.615,0.198 10 false *1
*1 Combination Switch Assembly


Remove the combination switch assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>COMBINATION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) on Below 1 Ω
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)
a.
C277026C03
0.458,0.927 0.854,1.177 0.396,0.25 2.177,1.75 1.927,1.333 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 2.01,1.792 2.625,1.99 0.615,0.198 10 MSW2 0.521,0.979 0.854,1.156 0.333,0.177 10 G60
*a Front view of wire harness connector
(to Combination Switch Assembly)


Disconnect the combination switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G60-4 (MSW2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)
a.
C197708C07
1.552,0.177 1.99,0.438 0.438,0.26 2.125,1.698 1.969,1.198 true 0.146,0.156 0.458,0.354 0.313,0.198 10 *a 1.625,0.219 2,0.448 0.375,0.229 10 A61 1.802,1.75 2.594,1.948 0.792,0.198 10 36 (PWMS)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A61-36 (PWMS) - Body ground Combination switch (SPORT) on Below 1 Ω
A61-36 (PWMS) - Body ground Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR