Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.
71940A
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the rear seat headrest assembly.
71845D
2.REMOVE REAR SEAT COVER CAP RH
| *1 | Protective Tape |
Using a screwdriver, detach the 3 claws to remove the rear seat cover cap RH.
Tape the screwdriver tip before use.
72525A
3.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the 3 screws and reclining adjuster release handle RH.
71691E
4.REMOVE REAR SEAT NO. 1 CUSHION HINGE COVER
Detach the 4 claws and guide to remove the rear seat No. 1 cushion hinge cover.
71692E
5.REMOVE REAR SEAT NO. 2 CUSHION HINGE COVER
Detach the 4 claws and guide to remove the rear seat No. 2 cushion hinge cover.
6.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
w/ Seat Heater System:
Disconnect the connector.
Detach the 4 clamps to disconnect the wire harness.
Detach the 18 hooks.
Remove the 3 hog rings and separate type seat cushion cover with pad from the rear seat cushion frame sub-assembly RH.
71075S
7.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog ring.
Remove the 13 hog rings and separate type rear seat cushion cover from the rear seat cushion pad RH.
87510Q
8.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
72996A
9.REMOVE REAR SEATBACK COVER
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws to remove the rear seatback cover.
Tape the screwdriver tip before use.
71015A
10.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Detach the cable clamp.
| *1 | Cable Clamp | *2 | Cable End |
| *3 | Clamp | - | - |
Disconnect the cable end in the order shown in the illustration.
Remove the 3 clamps to disconnect the No. 2 seat adjuster control cable assembly from the rear seat cushion frame sub-assembly RH.
Remove the 4 bolts, 4 bushes and rear seat cushion frame sub-assembly RH.
72996
11.REMOVE REAR SEATBACK COVER RH
w/o Child Restraint System Guide:
Remove the clip and screw.
Using a screwdriver, detach the claw to remove the rear seatback cover RH.
Tape the screwdriver tip before use.
w/ Child Restraint System Guide:
Remove the screw.
Detach the 4 claws to remove the rear seatback cover RH.
72995A
12.REMOVE REAR SEAT COVER
w/o Child Restraint System Guide:
Remove the clip and screw.
Using a screwdriver, detach the claw to remove the rear seat cover.
Tape the screwdriver tip before use.
w/ Child Restraint System Guide:
Remove the screw.
Detach the 4 claws to remove the rear seat cover.
71304C
13.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH (w/ Child Restraint System Guide)
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws to remove the rear seatback hinge sub-assembly LH.
Tape the screwdriver tip before use.
71303C
14.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH (w/ Child Restraint System Guide)
| *1 | Protective Tape |
Using a screwdriver, detach the 2 claws to remove the rear seatback hinge sub-assembly RH.
Tape the screwdriver tip before use.
71825B
15.REMOVE REAR SEAT CUSHION MOULDING RH
Using a screwdriver, detach the claw and 2 guides to remove the rear seat cushion moulding RH.
71828B
16.REMOVE REAR SEAT REAR CUSHION MOULDING RH
| *1 | Clamp |
| *2 | Guide |
w/ Seat Belt Warning System:
Detach the 2 clamps to disconnect the wire harness.
Detach the claw and guide to remove the rear seat rear cushion moulding RH.
72380
17.REMOVE NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY
| *1 | Cable Clamp A |
| *2 | Cable End |
| *3 | Clamp |
| *4 | Cable Clamp B |
Detach the 2 cable clamps (A).
Disconnect the 2 cable ends in the order shown in the illustration.
Remove the 2 clamps.
Detach the cable clamp (B).
Pass the No. 2 seat adjuster control cable assembly through the hole of the rear seat reclining adjuster assembly RH to remove the No. 2 seat adjuster control cable assembly.
73330C
18.REMOVE REAR SEAT CENTER LAP TYPE BELT ASSEMBLY RH
73380D
19.REMOVE REAR SEAT INNER BELT ASSEMBLY RH
20.REMOVE NO. 1 SEATBACK ASSEMBLY RH
Remove the 2 bolts and No. 1 seatback assembly RH from the rear seat reclining adjuster assembly RH.
71881
21.REMOVE REAR SEATBACK BOARD RH
Remove the 4 hog rings.
Open the 2 fasteners.
Detach the 5 claws.
Move the rear seatback board RH in the direction of the arrow to detach the guide and remove the rear seatback board assembly RH.
22.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
Detach the 6 hooks.
Detach the 4 claws to remove the 2 rear seat headrest supports.
Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly RH.
71077S
23.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the 2 hog rings.
Remove the 11 hog rings and separate type rear seatback cover from the rear seat cushion pad RH.
87510P
24.REMOVE REAR SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)