Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226926 SPEED LIMITER SYSTEM U

CRUISE CONTROL  SPEED LIMITER SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

for 2WW:

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

for 2WW:

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Switch Speed limiter switch signal ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-
Vehicle Speed Used for CCS and ASL Computation Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual vehicle speed displayed -
Speed Limit Stored by ASL Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Vehicle speed stored in memory -
Accelerator Pedal Angle for Speed Limiter Accelerator pedal angle Min.: 0 %, Max.: 100 % Accelerator pedal angle displayed -
ASL Main SW Speed limiter switch signal ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-

f.

for 3ZR-FAE:

Enter the following menus: Powertrain / Cruise Control / Data List.


g.

for 3ZR-FAE:

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual vehicle speed displayed -
ASL Memory Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Vehicle speed stored in memory -
ASL Throttle Position Throttle opening angle Min.: 0 deg., Max.: 124.5 deg Required throttle opening angle -
ASL Ready Speed limit standby condition ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-
ASL Main Switch Speed limiter switch signal ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-
ASL Shift Position Request Transaxle gear request signal Min.: 1, Max.: 8 Required transaxle gear for CVT


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other item to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform "Active Test" according to the display on GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -