Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

for LHD
E235206E25
1.042,1.792 1.479,1.958 0.438,0.167 10 false G145 1.042,1.969 2.219,2.344 1.177,0.375 10 false No. 1 Stereo Jack Adapter Assembly 5.156,1.792 5.656,1.958 0.5,0.167 10 false G190 5.198,1.323 5.896,1.49 0.698,0.167 10 false US1+ 5,1.229 5.208,1.396 0.208,0.167 10 false 3 5.208,0.781 5.792,0.979 0.583,0.198 10 false US1- 5,0.677 5.177,0.844 0.177,0.167 10 false 2 1.594,1.333 2.01,1.5 0.417,0.167 10 false UDO+ 2.073,1.229 2.281,1.396 0.208,0.167 10 false 3 1.604,0.781 2.021,0.948 0.417,0.167 10 false UDO- 2.073,0.677 2.281,0.844 0.208,0.167 10 false 2 5.156,1.958 6.365,2.51 1.208,0.552 10 false Radio and Display Receiver Assembly

for RHD
E235206E09
1.042,1.792 1.479,1.958 0.438,0.167 10 false G145 1.042,1.969 2.219,2.344 1.177,0.375 10 false No. 1 Stereo Jack Adapter Assembly 5.156,1.792 5.656,1.958 0.5,0.167 10 false G150 5.198,1.313 5.896,1.479 0.698,0.167 10 false UDO+ 5.01,1.229 5.219,1.396 0.208,0.167 10 false 3 5.198,0.76 5.781,0.958 0.583,0.198 10 false UDO- 5.01,0.677 5.188,0.844 0.177,0.167 10 false 2 1.604,1.313 2.021,1.479 0.417,0.167 10 false UDO+ 2.063,1.229 2.271,1.396 0.208,0.167 10 false 3 1.604,0.76 2.021,0.927 0.417,0.167 10 false UDO- 2.063,0.677 2.271,0.844 0.208,0.167 10 false 2 5.156,1.958 6.365,2.51 1.208,0.552 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G190*1 or G150*2 radio and display receiver assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G190-2 (US1-) - G145-2 (UDO-) Always Below 1 Ω
G190-3 (US1+) - G145-3 (UDO+) Always Below 1 Ω
G190-2 (US1-) - Body ground Always 10 kΩ or higher
G190-3 (US1+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G150-2 (UDO-) - G145-2 (UDO-) Always Below 1 Ω
G150-3 (UDO+) - G145-3 (UDO+) Always Below 1 Ω
G150-2 (UDO-) - Body ground Always 10 kΩ or higher
G150-3 (UDO+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR