Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Using this circuit, the radio and display receiver assembly sends power to the map light assembly, and the roof console box assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E273268E08
1.573,1.177 2.042,1.365 0.469,0.188 10 false MACC 1.583,1.646 2.021,1.833 0.438,0.188 10 false MCO+ 1.615,2.135 2.021,2.344 0.406,0.208 10 false MCO- 1.594,3.094 2.063,3.281 0.469,0.188 10 false SNS2 0.698,1.969 1.417,2.542 0.719,0.573 10 false Telephone Microphone Assembly 0.552,3.646 0.917,3.833 0.365,0.188 10 false Q16 0.563,3.833 1.906,4.063 1.344,0.229 10 false Map Light Assembly 3.031,2.854 3.625,3.083 0.594,0.229 10 false Shielded 4.573,2.865 5.167,3.094 0.594,0.229 10 false Shielded 5.75,3.833 6.958,4.198 1.208,0.365 10 false Radio and Display Receiver Assembly 5.75,3.656 6.115,3.844 0.365,0.188 10 false G143 6,1.302 6.469,1.49 0.469,0.188 10 false MACC 6.031,1.781 6.5,1.969 0.469,0.188 10 false MIN+ 6.052,2.24 6.521,2.427 0.469,0.188 10 false MIN- 6.042,2.74 6.51,2.927 0.469,0.188 10 false SGND 6.042,3.198 6.51,3.385 0.469,0.188 10 false SNS2 5.75,1.177 5.906,1.354 0.156,0.177 10 false 4 5.75,1.656 5.906,1.833 0.156,0.177 10 false 5 5.698,2.115 5.938,2.292 0.24,0.177 10 false 19 5.698,2.604 5.938,2.781 0.24,0.177 10 false 18 5.76,3.094 6,3.271 0.24,0.177 10 false 6 2.094,1.177 2.563,1.365 0.469,0.188 10 false 3 2.104,1.656 2.573,1.844 0.469,0.188 10 false 4 2.094,2.135 2.563,2.323 0.469,0.188 10 false 6 2.094,3.094 2.563,3.281 0.469,0.188 10 false 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω
G143-4 (MACC) - Q16-3 (MACC) Always Below 1 Ω
G143-5 (MIN+) - Q16-4 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - Q16-6 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Body ground Always 10 kΩ or higher
G143-4 (MACC) - Body ground Always 10 kΩ or higher
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly with its connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E237416C03
1.406,0.448 1.865,0.688 0.458,0.24 2.25,1.771 2.719,0.865 true 2.219,2 2.5,2.667 true 1.333,2.615 2.052,1.979 true 0.083,0.094 0.396,0.292 0.313,0.198 10 *a 1.469,0.479 1.875,0.667 0.406,0.188 10 G143 2.781,0.771 3.281,1 0.5,0.229 10 MACC 2.542,2.594 3.01,2.771 0.469,0.177 10 SGND 1,2.521 1.333,2.76 0.333,0.24 10 MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-18 (SGND) - Body ground Always Below 1 Ω
G143-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT MAP LIGHT ASSEMBLY
a.
E333810E01
1.156,0.281 1.323,0.281 1.323,0.281 1.625,1.042 true 2.313,0.281 2.115,0.281 2.115,0.281 1.854,1.042 true 2.365,0.198 2.979,0.396 0.615,0.198 10 false SNS2 0.729,0.208 1.344,0.406 0.615,0.198 10 false MCO-

Remove the map light assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SNS2) - 6 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MAP LIGHT ASSEMBLY

NG

7.CHECK TELEPHONE MICROPHONE ASSEMBLY
4.CHECK MAP LIGHT ASSEMBLY
a.
E333811C01
1.552,0.083 1.927,0.354 0.375,0.271 1.063,1.75 1.25,1.75 1.25,1.75 1.625,0.958 true 2.531,1.75 2.354,1.75 2.354,1.75 2.031,0.958 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 1.615,0.135 2.073,0.333 0.458,0.198 10 false Q16 0.615,1.677 1.229,1.875 0.615,0.198 10 false MCO- 2.583,1.667 3.198,1.865 0.615,0.198 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with its connector still connected.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals 4 (MCO+) and 6 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output A
A waveform synchronized with the voice input to the map light assembly is not output B



A

B

5.CHECK TELEPHONE MICROPHONE ASSEMBLY
5.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


Result:
Proceed to
Malfunction disappears
Malfunction appears



Malfunction disappears

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

Malfunction appears

6.CHECK MAP LIGHT ASSEMBLY
6.CHECK MAP LIGHT ASSEMBLY
a.

Replace the map light assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


Result:
Proceed to
Malfunction disappears
Malfunction appears



Malfunction disappears

END (MAP LIGHT ASSEMBLY IS DEFECTIVE)

Malfunction appears

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


Result:
Proceed to
Malfunction disappears
Malfunction appears



Malfunction disappears

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

Malfunction appears