Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING › from 2015.10
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050282 WHEEL OPENING MOULDING A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 53853C 1.INSTALL FRONT WHEEL NO. 3 OPENING EXTENSION PAD

HINT:

When installing the front wheel No. 3 opening extension pad, heat the front fender front outside moulding LH using a heat light.


Standard:
Item Temperature
Front Fender Front Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front fender front outside moulding LH excessively.


a.

Clean the front fender front outside moulding LH surface.

i.

Using a heat light, heat the front fender front outside moulding LH surface.


ii.

Remove the double-sided tape from the front fender front outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422093C01
2.938,1.656 2.865,1.927 2.865,1.927 2.5,1.375 true 1.51,1.729 2.073,1.604 2.073,1.604 1.698,1.479 true 2.792,1.917 3.104,2.115 0.313,0.198 10 false *a 2.125,1.531 2.438,1.729 0.313,0.198 10 false *a 2.948,0.927 3.26,1.125 0.313,0.198 10 false *c 1.042,1.188 1.354,1.385 0.313,0.198 10 false *b
*a Mark-off Line
*b 3.0 mm (0.118 in.)
*c 10.0 mm (0.394 in.)


Install a new front wheel No. 3 opening extension pad.

i.

Using a heat light, heat the front fender front outside moulding LH.


ii.

Remove the peeling paper from the face of the front wheel No. 3 opening extension pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Align the front wheel opening No. 3 extension pad with the mark-off line of the front fender front outside moulding LH, and then install it.

HINT:

Press the front wheel No. 3 opening extension pad firmly to install it.




Hide 53855B 2.INSTALL FRONT WHEEL NO. 5 OPENING EXTENSION PAD

HINT:

When installing the front wheel No. 5 opening extension pad, heat the front fender front outside moulding LH using a heat light.


Standard:
Item Temperature
Front Fender Front Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front fender front outside moulding LH excessively.


a.

Clean the front fender front outside moulding LH surface.

i.

Using a heat light, heat the front fender front outside moulding LH surface.


ii.

Remove the double-sided tape from the front fender front outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B427254C01
1.24,0.917 1.323,1.771 1.323,1.771 1.406,0.823 true 0.302,0.938 0.385,1.781 0.385,1.781 0.427,0.917 true 1.26,1.802 1.573,2 0.313,0.198 10 false *a 0.313,1.813 0.625,2.01 0.313,0.198 10 false *a 0.281,0.313 0.594,0.51 0.313,0.198 10 false *b 0.969,0.292 1.281,0.49 0.313,0.198 10 false *c
*a Mark-off Line
*b 4.0 mm (0.157 in.)
*c 3.0 mm (0.118 in.)


Install a new front wheel No. 5 opening extension pad.

i.

Using a heat light, heat the front fender front outside moulding LH.


ii.

Remove the peeling paper from the face of the front wheel No. 5 opening extension pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Align the front wheel opening No. 5 extension pad with the mark-off line of the front fender front outside moulding LH, and then install it.

HINT:

Press the front wheel No. 5 opening extension pad firmly to install it.




Hide 53851W 3.INSTALL FRONT WHEEL NO. 1 OPENING EXTENSION PAD

HINT:

When installing the front wheel No. 1 opening extension pad, heat the front fender front outside moulding LH using a heat light.


Standard:
Item Temperature
Front Fender Front Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front fender front outside moulding LH excessively.


a.

Clean the front fender front outside moulding LH surface.

i.

Using a heat light, heat the front fender front outside moulding LH surface.


ii.

Remove the double-sided tape from the front fender front outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422090C01
2.375,1.25 3.031,0.531 3.031,0.531 2.49,1.313 true 3.094,0.438 3.333,0.656 0.24,0.219 10 false *a 2.125,1.76 2.365,1.979 0.24,0.219 10 false *b 3.115,1.188 3.281,1.438 0.167,0.25 10 true *c
*a Mark-off Line
*b 2.0 mm (0.0787 in.)
*c 2.0 mm (0.0787 in.)


Install a new front wheel No. 1 opening extension pad.

i.

Using a heat light, heat the front fender front outside moulding LH.


ii.

Remove the peeling paper from the face of the front wheel No. 1 opening extension pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front wheel No. 1 opening extension pad.

HINT:

Press the front wheel No. 1 opening extension pad firmly to install it.




Hide 75696C 4.INSTALL NO. 1 BODY OUTSIDE MOULDING PAD

HINT:

When installing the No. 1 body outside moulding pad, heat the center quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Center Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the center quarter outside moulding LH excessively.


a.

Clean the center quarter outside moulding LH surface.

i.

Using a heat light, heat the center quarter outside moulding LH surface.


ii.

Remove the double-sided tape from the center quarter outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422095C01
0.823,0.677 1.25,0.74 1.25,0.74 0.75,0.771 true 3.021,0.698 3.031,1.177 3.031,1.177 2.615,0.719 true 1.292,0.646 1.604,0.844 0.313,0.198 10 false *a 2.958,1.198 3.271,1.396 0.313,0.198 10 false *a 0.188,0.271 0.5,0.469 0.313,0.198 10 false *b 2.813,0.146 3.125,0.344 0.313,0.198 10 false *c
*a Mark-off Line
*b 3.0 mm (0.118 in.)
*c 10.0 mm (0.394 in.)


Install a new No. 1 body outside moulding pad.

i.

Using a heat light, heat the center quarter outside moulding LH.


ii.

Remove the peeling paper from the face of the No. 1 body outside moulding pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the No. 1 body outside moulding pad.

HINT:

Press the No. 1 body outside moulding pad firmly to install it.




Hide 75697D 5.INSTALL NO. 2 BODY OUTSIDE MOULDING PAD

HINT:

When installing the No. 2 body outside moulding pad, heat the center quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Center Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the center quarter outside moulding LH excessively.


a.

Clean the center quarter outside moulding LH surface.

i.

Using a heat light, heat the center quarter outside moulding LH surface.


ii.

Remove the double-sided tape from the center quarter outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422097C01
0.521,1.688 1.073,1.823 1.073,1.823 0.635,1.792 true 2.688,0.927 2.729,1.75 2.729,1.75 2.76,1.146 true 1.135,1.75 1.448,1.948 0.313,0.198 10 false *a 2.667,1.76 2.979,1.958 0.313,0.198 10 false *a 0.594,1.125 0.906,1.323 0.313,0.198 10 false *b 3.063,0.802 3.375,1 0.313,0.198 10 false *c
*a Mark-off Line
*b 3.0 mm (0.118 in.)
*c 10.0 mm (0.394 in.)


Install a new No. 2 body outside moulding pad.

i.

Using a heat light, heat the center quarter outside moulding LH.


ii.

Remove the peeling paper from the face of the No. 2 body outside moulding pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the No. 2 body outside moulding pad.

HINT:

Press the No. 2 body outside moulding pad firmly to install it.




Hide 75698B 6.INSTALL NO. 3 BODY OUTSIDE MOULDING PAD

HINT:

When installing the No. 3 body outside moulding pad, heat the center quarter outside moulding LH using a heat light.


Standard:
Item Temperature
Center Quarter Outside Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the center quarter outside moulding LH excessively.


a.

Clean the center quarter outside moulding LH surface.

i.

Using a heat light, heat the center quarter outside moulding LH surface.


ii.

Remove the double-sided tape from the center quarter outside moulding LH.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B422099C01
1.854,0.635 1.406,0.448 1.406,0.448 1.844,0.49 true 2.208,1.688 1.813,1.344 1.813,1.344 2.24,1.49 true 1.229,0.354 1.542,0.552 0.313,0.198 10 false *a 1.656,1.24 1.969,1.438 0.313,0.198 10 false *a 2.427,0.49 2.74,0.688 0.313,0.198 10 false *b 2.802,1.5 3.115,1.698 0.313,0.198 10 false *c
*a Mark-off Line
*b 3.0 mm (0.118 in.)
*c 6.0 mm (0.236 in.)


Install a new No. 3 body outside moulding pad.

i.

Using a heat light, heat the center quarter outside moulding LH.


ii.

Remove the peeling paper from the face of the No. 3 body outside moulding pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the No. 3 body outside moulding pad.

HINT:

Press the No. 3 body outside moulding pad firmly to install it.