Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER(for RHD) › from 2015.10
RM3090E _52 Drivetrain _008754 CLUTCH _0050266 CLUTCH MASTER CYLINDER(for RHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for RHD)  INSTALLATION  


PROCEDURE

Hide 31453 1.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.
C279738

Install the lock nut to the clutch master cylinder assembly.


b.

Install the clutch master cylinder push rod clevis to the clutch master cylinder assembly.


c.
C125987C02
1.646,1.135 1.531,0.5 1.531,0.5 1.271,0.5 false 2.229,0.875 2.115,0.24 2.115,0.24 1.854,0.24 false 1.01,0.417 1.323,0.615 0.313,0.198 10 *1 1.615,0.146 1.927,0.344 0.313,0.198 10 *2 1.115,1.844 1.427,2.042 0.313,0.198 10 A
*1 Lock Nut
*2 Clutch Master Cylinder Push Rod Clevis


Tighten the lock nut and check that dimension A is the same as the dimension A that has been measured.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

When tightening the lock nut, be sure to hold the clevis in place by its square portion.



Hide 31459 2.INSTALL CLUTCH MASTER CYLINDER BRACKET

a.

Install the clutch master cylinder bracket to the clutch master cylinder assembly.


Hide 31453 3.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.

Apply MP grease to the contact surface of the clutch master cylinder push rod clevis and the clutch pedal assembly.


b.
C279743C01
1.927,1.417 1.958,1.323 false
V100135

MP grease


Install the clutch master cylinder push rod clevis to the cutout of the clutch pedal assembly from the left side of the vehicle and push it downward.


Hide 31410 4.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.

Install the clutch master cylinder assembly with the 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 31481 5.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.

Using a union nut wrench, connect the clutch master cylinder to flexible hose tube.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench. Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 31434 6.CONNECT CLUTCH RESERVOIR TUBE

a.

Connect the clutch reservoir tube to the clutch master cylinder assembly, and slide the clamp to secure it.

NOTICE:
·

Connect the clutch reservoir tube so that it will not be twisted.

·

Face the yellow mark upward.




Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 89871A 8.INSTALL INJECTOR DRIVER

Hide 47287 11.CHECK BRAKE FLUID

a.

Check the brake fluid. Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING

HINT:
·

Check for leakage in the brake system.

·

Check for leakage in the clutch system.




Hide 47287 12.CHECK FLUID LEVEL IN RESERVOIR

Hide 31301 13.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY