Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


a.
B268088E09
1.573,0.26 2.01,0.5 0.438,0.24 1.667,0.313 1.958,0.521 0.292,0.208 10 G24

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC

*1: except Manual Transaxle

*2: for Manual Transaxle

G24-6 (AGND) - Body ground - BR - Body ground Transponder key amplifier ground Always Below 1 Ω -
G24-7 (TXCT) - G24-6 (AGND) Input L - BR Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G24-8 (CODE) - G24-6 (AGND) Output W - BR Immobiliser communication output Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G24-10 (VC5) - G24-6 (AGND) Input R - BR Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G24-7 (TXCT) - G24-6 (AGND) Input L - BR Signal input from certification ECU (smart key ECU assembly) (Code sent from certification ECU [smart key ECU assembly] to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above


G24-8 (CODE) - G24-6 (AGND) Output W - BR Signal output to certification ECU (smart key ECU assembly) (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU [smart key ECU assembly]) Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
G24-10 (VC5) - G24-6 (AGND) Input R - BR Transponder key amplifier power supply (Power supplied from certification ECU [smart key ECU assembly] when transponder key amplifier built into engine switch activated) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



HINT:

*: Remove the key battery before performing this inspection.



c.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G24-7 (TXCT) - G24-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418C17
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false
*a Key held near engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G24-8 (CODE) - G24-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G24-10 (VC5) - G24-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B264892N71
1.958,0.729 2.354,0.969 0.396,0.24 3.344,0.729 3.74,0.969 0.396,0.24 4.917,0.729 5.313,0.969 0.396,0.24 2.052,0.781 2.76,1.25 0.708,0.469 10 G82 3.448,0.781 4.042,1.219 0.594,0.438 10 G83 5.01,0.781 5.646,1.229 0.635,0.448 10 G84

a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G82-2 (+B) - G82-11 (E) Input W - BR +B power supply Always 11 to 14 V -
G82-10 (CUTB) - G82-11 (E) Input P - BR Dark current cut pin Always 11 to 14 V -
G82-11 (E) - Body ground - BR - Body ground Ground Always Below 1 Ω -


c.

Reconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC

*1: except Manual Transaxle

*2: for Manual Transaxle

*3: w/o ID code box (Immobiliser Code ECU)

G84-5 (IG) - G82-11 (E) Input LG - BR Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
G84-18 (IND) - G82-11 (E) Output GR - BR Security indicator output Engine switch off → on (IG) Pulse generation→ Below 2 V -
G84-9 (TXCT) - G84-24 (AGND) Output L - BR Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G84-7 (CODE) - G84-24 (AGND) Input W - BR Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G84-1 (VC5) - G84-24 (AGND) Output R - BR Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G84-24 (AGND) - Body ground - BR - Body ground Transponder key amplifier ground Always Below 1 Ω -
G82-14 (EFII) - G82-11 (E)*3 Input LG - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G82-13 (EFIO) - G82-11 (E)*3 Output P - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Engine switch off Below 1 V


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G84-9 (TXCT) - G84-24 (AGND) Output L - BR Signal output to transponder key amplifier (Code sent from certification ECU [smart key ECU assembly] to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G84-7 (CODE) - G84-24 (AGND) Input W - BR Signal input from transponder key amplifier (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU [smart key ECU assembly].) Engine switch off, engine switch pressed with key held near engine switch*1 Pulse generation
(See waveform 2)
G84-1 (VC5) - G84-24 (AGND) Output R - BR Transponder key amplifier power supply (Power supplied from certification ECU [smart key ECU assembly] when transponder key amplifier built into engine switch activated) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
G82-14 (EFII) - G82-11 (E)*2 Input LG - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 4)
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G82-13 (EFIO) - G82-11 (E)*2 Output P - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 5)

HINT:
·

*1: Remove the key battery before performing this inspection.

·

*2: w/o ID code box (Immobiliser Code ECU)




f.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E17
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G84-9 (TXCT) - G84-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418C16
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false
*a Key held near engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G84-7 (CODE) - G84-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G84-1 (VC5) - G84-24 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


iv.

Waveform 4 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G82-14 (EFII) - G82-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


v.

Waveform 5 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G82-13 (EFIO) - G82-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID code box [Immobiliser Code ECU])


a.

Disconnect the G44 ID code box (immobiliser code ECU) connector.


b.
B302477N02
1.542,0.563 1.938,0.771 0.396,0.208 1.615,0.583 2.073,0.781 0.458,0.198 10 G44

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC

If the result is not as specified, there may be a malfunction on the wire harness side.

G44-1 (+B) - Body ground Input BE - Body ground +B power supply Engine switch off 11 to 14 V B2789
G44-5 (GND) - Body ground - B - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the G44 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G44-3 (EFII) - G44-5 (GND) Input LG - B EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G44-4 (EFIO) - G44-5 (GND) Output P - B EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Engine switch off Below 1 V
G44-3 (EFII) - G44-5 (GND) Input LG - B EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1)
G44-4 (EFIO) - G44-5 (GND) Output P - B EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2)


e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G44-3 (EFII) - G44-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G44-4 (EFIO) - G44-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


a.
B269095N06
1.552,0.271 1.885,0.521 0.333,0.25 1.615,0.323 1.927,0.521 0.313,0.198 10 G5

Measure the voltage and resistance and check the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G5-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G5-3 (IGE) - G5-1 (GND) Input Y - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU [smart key ECU assembly])
Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P (except Manual Transaxle)

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation (See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G5-4 (SLP1) - G5-1 (GND) Output G - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked* 11 to 14 V → Below 1.2 V
·

Push Start Error

·

Sensor Value


G5-6 (IG2) - G5-1 (GND) Input P - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V
·

B2788

·

Ignition Switch


G5-7 (B) - Body ground Output L - Body ground Constant power supply Always 11 to 14 V B2788

HINT:

*: The steering locks when any door is opened with the shift lever in P (except Manual Transaxle) and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content

*: except Manual Transaxle

Tester Connection G5-3 (IGE) - G5-1 (GND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition
Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off






CHECK ECM (for 2AR-FE)


C228683E04
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B77

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A62-3 (+B2) - B77-16 (E1) Input P - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-2 (+B) - B77-16 (E1) Input R - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-46 (MREL) - B77-16 (E1) Input P - BR EFI MAIN1 relay Engine switch on (IG) 11 to 14 V -
A62-1 (BATT) - B77-16 (E1) Input W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
B77-16 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A62-29 (IMO) - B77-16 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A62-29 (IMO) - B77-16 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1) -
A62-28 (IMI) - B77-16 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A62-28 (IMI) - B77-16 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2) -

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-29 (IMO) - B77-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-28 (IMI) - B77-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 3ZR-FE [for K111, K111F])


C228683E05
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B75

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A62-3 (+B2) - B75-16 (E1) Input P - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-2 (+B) - B75-16 (E1) Input R - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-46 (MREL) - B75-16 (E1) Input P - BR EFI MAIN1 relay Engine switch on (IG) 11 to 14 V -
A62-1 (BATT) - B75-16 (E1) Input W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
B75-16 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A62-29 (IMO) - B75-16 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A62-29 (IMO) - B75-16 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1) -
A62-28 (IMI) - B75-16 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A62-28 (IMI) - B75-16 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2) -

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-29 (IMO) - B75-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-28 (IMI) - B75-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 3ZR-FE [except K111, K111F], 3ZR-FAE)


C228683E07
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 5.375,0.302 5.833,0.5 0.458,0.198 10 false A62 2.552,0.292 3.01,0.49 0.458,0.198 10 false B93

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A62-3 (+B2) - B93-59 (E1) Input P - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-2 (+B) - B93-59 (E1) Input R - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-46 (MREL) - B93-59 (E1) Input P - BR EFI MAIN1 relay Engine switch on (IG) 11 to 14 V -
A62-1 (BATT) - B93-59 (E1) Input W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
B93-59 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A62-45 (IMO) - B93-59 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A62-45 (IMO) - B93-59 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1) -
A62-28 (IMI) - B93-59 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A62-28 (IMI) - B93-59 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2) -

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-45 (IMO) - B93-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-28 (IMI) - B93-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 2AD-FHV, 2AD-FTV [for DPF], 2AD-FTV [for CCo])


C159489E29
2.344,0.385 2.76,0.656 0.417,0.271 4.781,0.458 5.198,0.729 0.417,0.271 4.854,0.521 5.323,0.719 0.469,0.198 10 A61 2.438,0.438 2.906,0.635 0.469,0.198 10 B76

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A61-20 (+B2) - B76-109 (E1) Input B - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A61-1 (+B) - B76-109 (E1) Input B - BR Power source of ECM Engine switch on (IG) 11 to 14 V -
A61-45 (MREL) - B76-109 (E1) Input B - BR EFI MAIN1 relay Engine switch on (IG) 11 to 14 V -
A61-2 (BATT) - B76-109 (E1) Input W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
B76-109 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A61-15 (IMO) - B76-109 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A61-15 (IMO) - B76-109 (E1) Input LG - BR Certification ECU (smart key ECU assembly) communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1) -
A61-16 (IMI) - B76-109 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A61-16 (IMI) - B76-109 (E1) Output P - BR Certification ECU (smart key ECU assembly) communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2) -

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A61-15 (IMO) - B76-109 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A61-16 (IMI) - B76-109 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 2WW)


A318632E05
2.563,0.573 3.052,0.875 0.49,0.302 5.365,0.573 5.854,0.865 0.49,0.292 2.656,0.646 3.042,0.844 0.385,0.198 10 false B112 5.479,0.635 5.802,0.833 0.323,0.198 10 false A62

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A62-14 (+B2) - B112-4 (E1) Input B - W-B Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-2 (+B) - B112-4 (E1) Input B - W-B Power source of ECM Engine switch on (IG) 11 to 14 V -
A62-9 (MREL) - B112-4 (E1) Input B - W-B EFI MAIN1 relay Engine switch on (IG) 11 to 14 V -
A62-15 (BATT) - B112-4 (E1) Input W - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
B112-4 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A62-44 (IMO) - B112-4 (E1) Input LG - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A62-44 (IMO) - B112-4 (E1) Input LG - W-B Certification ECU (smart key ECU assembly) communication input Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 1) -
A62-34 (IMI) - B112-4 (E1) Output P - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A62-34 (IMI) - B112-4 (E1) Output P - W-B Certification ECU (smart key ECU assembly) communication output Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation (See waveform 2) -

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-44 (IMO) - B112-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A62-34 (IMI) - B112-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal