Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short
The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU [smart key ECU assembly]) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation:
With the shift lever in P (except Manual Transaxle), the key is held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P (except Manual Transaxle) -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

B271004E17
5.052,3.031 6.573,3.396 1.521,0.365 10 Certification ECU (Smart Key ECU Assembly) 5.052,2.833 5.333,3.01 0.281,0.177 10 G84 0.792,2.823 1.073,3 0.281,0.177 10 G24 0.802,3.021 1.781,3.219 0.979,0.198 10 Engine Switch 5.302,2.271 5.75,2.438 0.448,0.167 10 AGND 1.458,1.771 1.906,1.938 0.448,0.167 10 CODE 1.521,1.26 1.969,1.427 0.448,0.167 10 TXCT 1.573,0.75 2.021,0.917 0.448,0.167 10 VC5 5.302,1.76 5.75,1.927 0.448,0.167 10 CODE 5.302,1.25 5.75,1.417 0.448,0.167 10 TXCT 5.302,0.75 5.75,0.917 0.448,0.167 10 VC5 1.448,2.26 1.896,2.427 0.448,0.167 10 AGND 1.917,0.667 2.365,0.833 0.448,0.167 10 10 1.938,1.167 2.385,1.333 0.448,0.167 10 7 1.938,1.688 2.385,1.854 0.448,0.167 10 8 1.938,2.208 2.385,2.375 0.448,0.167 10 6 5.052,0.667 5.5,0.833 0.448,0.167 10 1 5.083,1.177 5.531,1.344 0.448,0.167 10 9 5.083,1.688 5.531,1.854 0.448,0.167 10 7 5.083,2.208 5.531,2.375 0.448,0.167 10 24

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G24 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-7 (CODE) - G24-8 (CODE) Always Below 1 Ω
G84-9 (TXCT) - G24-7 (TXCT) Always Below 1 Ω
G84-1 (VC5) - G24-10 (VC5) Always Below 1 Ω
G84-24 (AGND) - G24-6 (AGND) Always Below 1 Ω
G84-7 (CODE) - Body ground Always 10 kΩ or higher
G24-8 (CODE) - Body ground Always 10 kΩ or higher
G84-9 (TXCT) - Body ground Always 10 kΩ or higher
G24-7 (TXCT) - Body ground Always 10 kΩ or higher
G84-1 (VC5) - Body ground Always 10 kΩ or higher
G24-10 (VC5) - Body ground Always 10 kΩ or higher
G84-24 (AGND) - Body ground Always 10 kΩ or higher
G24-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE ENGINE SWITCH

NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2784 is not output
DTC B2784 is output



DTC B2784 is not output

END (ENGINE SWITCH WAS DEFECTIVE)

DTC B2784 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)