Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*).
·

Harness or connector

·

Engine switch

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation:
With the shift lever in P (except Manual Transaxle), the key is held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P (except Manual Transaxle) -

Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

B271005E19
0.927,2.99 1.969,3.396 1.042,0.406 10 Engine Switch 0.927,2.823 1.354,3.021 0.427,0.198 10 G24 1.583,1.167 2.063,1.417 0.479,0.25 10 VC5 1.458,2.083 1.917,2.458 0.458,0.375 10 AGND 1.938,1.042 2.188,1.229 0.25,0.188 10 10 1.948,1.969 2.125,2.146 0.177,0.177 10 6 5.063,1.042 5.313,1.229 0.25,0.188 10 1 5.052,1.979 5.302,2.156 0.25,0.177 10 24 5.323,2.083 5.833,2.406 0.51,0.323 10 AGND 5.052,3.01 6.594,3.51 1.542,0.5 10 Certification ECU (Smart Key ECU Assembly) 5.052,2.833 5.396,3.083 0.344,0.25 10 G84 5.323,1.167 5.74,1.531 0.417,0.365 10 VC5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G24 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-1 (VC5) - G24-10 (VC5) Always Below 1 Ω
G84-24 (AGND) - G24-6 (AGND) Always Below 1 Ω
G84-1 (VC5) - Body ground Always 10 kΩ or higher
G24-10 (VC5) - Body ground Always 10 kΩ or higher
G84-24 (AGND) - Body ground Always 10 kΩ or higher
G24-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G24 engine switch and G84 certification ECU (smart key ECU assembly) connector.


b.
B271009C06
1.26,0.156 1.729,0.479 0.469,0.323 1.833,1.656 2.406,2.042 false 1.208,1.656 0.635,2.052 false 1.354,0.25 1.792,0.5 0.438,0.25 10 G24 0.125,0.125 0.385,0.375 0.26,0.25 10 *a 2.969,3.292 3.385,3.563 0.417,0.271 10 GND 0.323,2.021 0.719,2.25 0.396,0.229 10 VC5 2.448,1.979 3.01,2.208 0.563,0.229 10 AGND
*a Component with harness connected
(Engine Switch)


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition
Item Content
Tester Connection G24-10 (VC5) - G24-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK (for 2AR-FE)
OK (for 3ZR-FAE)
OK (for 3ZR-FE)
OK (for 2WW)
OK (for 2AD-FTV)
OK (for 2AD-FHV)
NG



OK (for 2AR-FE)

OK (for 3ZR-FAE)

OK (for 3ZR-FE)

OK (for 2WW)

OK (for 2AD-FTV)

OK (for 2AD-FHV)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)