Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (steering pad switch assembly) is on.

·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer rear view mirror sub-assembly RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Blind spot monitor sensor RH

·

Harness or connector



WIRING DIAGRAM

E270468E12
0.792,2.438 3.313,2.854 2.521,0.417 10 false Outer Rear View Mirror Sub-assembly RH (Outer Rear View Mirror Indicator RH) 0.979,3.729 3.458,3.948 2.479,0.219 10 false Outer Rear View Mirror Assembly RH 3.448,1.49 3.896,1.719 0.448,0.229 10 false BSR+ 3.719,1.917 3.875,2.115 0.156,0.198 10 false - 5.448,1.583 6.063,1.781 0.615,0.198 10 false OMIR 4.948,3.719 6.844,3.958 1.896,0.24 10 false Blind Spot Monitor Sensor RH 4.948,3.521 5.26,3.719 0.313,0.198 10 false T1 5.24,1.49 5.396,1.688 0.156,0.198 10 false 4 3.063,1.49 3.219,1.688 0.156,0.198 10 false 1 3.073,1.896 3.229,2.094 0.156,0.198 10 false 2 2.906,1.573 3.135,1.802 0.229,0.229 10 false + 2.917,1.969 3.073,2.167 0.156,0.198 10 false - 3.927,1.469 5.156,1.667 1.229,0.198 10 false 1*1, 7*2 3.938,1.875 5.313,2.073 1.375,0.198 10 false 8*1, 15*2 0.99,3.542 2.677,3.74 1.688,0.198 10 false I8*1, I14*2 0.063,4.063 5.719,4.26 5.656,0.198 10 false *1: w/o Panoramic View Monitor System 0.073,4.385 5.729,4.583 5.656,0.198 10 false *2: w/ Panoramic View Monitor System

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

DTCs are output

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR RH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR RH CIRCUIT)
a.

Disconnect the T1 blind spot monitor sensor RH connector.


b.

Disconnect the I8*1 or I14*2 outer rear view mirror sub-assembly RH connector.

*1: w/o Panoramic View Monitor System

*2: w/ Panoramic View Monitor System



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T1-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH
a.

Remove the outer rear view mirror sub-assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer rear view mirror sub-assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

DTCs are output