Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.10–2016.08
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB4 Open in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor system is on.

·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.


·

Outer rear view mirror sub-assembly LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Blind spot monitor sensor LH

·

Harness or connector



WIRING DIAGRAM

E270468E11
0.792,2.438 3.313,2.854 2.521,0.417 10 false Outer Rear View Mirror Sub-assembly LH (Outer Rear View Mirror Indicator LH) 0.979,3.729 3.458,3.948 2.479,0.219 10 false Outer Rear View Mirror Assembly LH 3.448,1.49 3.896,1.719 0.448,0.229 10 false BSL+ 3.719,1.917 3.875,2.115 0.156,0.198 10 false - 5.448,1.583 6.063,1.781 0.615,0.198 10 false OMIL 4.948,3.719 6.844,3.958 1.896,0.24 10 false Blind Spot Monitor Sensor LH 4.948,3.521 5.26,3.719 0.313,0.198 10 false R1 5.24,1.49 5.396,1.688 0.156,0.198 10 false 4 3.063,1.49 3.219,1.688 0.156,0.198 10 false 1 3.073,1.896 3.229,2.094 0.156,0.198 10 false 2 2.906,1.573 3.135,1.802 0.229,0.229 10 false + 2.917,1.969 3.073,2.167 0.156,0.198 10 false - 3.906,1.469 5.135,1.667 1.229,0.198 10 false 1*1, 7*2 3.938,1.875 5.313,2.073 1.375,0.198 10 false 8*1, 15*2 0.99,3.531 2.677,3.729 1.688,0.198 10 false J8*1, J14*2 0.073,4.083 2.552,4.302 2.479,0.219 10 false *1: w/o Panoramic View Monitor System 0.073,4.406 2.552,4.625 2.479,0.219 10 false *2: w/ Panoramic View Monitor System

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

DTCs are output

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Disconnect the J8*1 or J14*2 outer rear view mirror assembly LH connector.

*1: w/o Panoramic View Monitor System

*2: w/ Panoramic View Monitor System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Panoramic View Monitor System
Tester Connection Condition Specified Condition
R1-4 (OMIL) - J8-1 (BSL+) Always Below 1 Ω


Standard Resistance:
w/ Panoramic View Monitor System
Tester Connection Condition Specified Condition
R1-4 (OMIL) - J14-1 (BSL+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
a.

Remove the outer rear view mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer rear view mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Replace the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

DTCs are output

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH