INSPECT SET SWITCH
Push the cruise control switch to on.
| *1 | Cruise Control Indicator Light |
Check that the cruise control indicator light illuminates on the combination meter assembly.
Drive the vehicle at a desired speed (between approximately 40 km/h and 200 km/h [25 mph and 125 mph]).
Press the cruise control switch to -SET.
| *1 | Cruise Control SET Indicator Light |
Check that the cruise control SET indicator light illuminates at this time.
After releasing the switch, check that the vehicle cruises at the desired speed.
INSPECT "+" SWITCH
Push the cruise control switch to on.
Drive the vehicle at a desired speed (between approximately 40 km/h and 200 km/h [25 mph and 125 mph]).
Press the cruise control switch to -SET.
Check that the vehicle speed increases while the cruise control switch is pulled up to +RES, and that the vehicle cruises at the set speed when the switch is released.
Momentarily press the cruise control switch upward to +RES and then immediately release it. Check that the vehicle speed increases by approximately 1 km/h (or 1 mph)*1 or 1.6 km/h (1.0 mph)*2 (Tap-up function).
*1: except 3ZR-FE (K111), 2WW
*2: for 3ZR-FE (K111), 2WW
INSPECT "-" SWITCH
Push the cruise control control switch to on.
Drive the vehicle at a desired speed (between approximately 40 km/h and 200 km/h [25 mph and 125 mph]).
Press the cruise control switch to -SET.
Check that the vehicle speed decreases while the cruise control switch is pushed down to -SET, and the vehicle cruises at the set speed when the switch is released.
Momentarily press the cruise control switch downward to -SET, and then immediately release it. Check that the vehicle speed decreases by approximately 1 km/h (or 1 mph)*1 or 1.6 km/h (1.0 mph)*2 (Tap-down function).
*1: except 3ZR-FE (K111), 2WW
*2: for 3ZR-FE (K111), 2WW
INSPECT CANCEL SWITCH
Push the cruise control switch to on.
Drive the vehicle at a desired speed (between approximately 40 km/h and 200 km/h [25 mph and 125 mph]).
Press the cruise control switch to -SET.
When performing one of the following, check that the cruise control system is canceled and that the normal driving mode is reset.
Depressing the brake pedal.
for Manual Transaxle:
Depressing the clutch pedal.
for U760F, U760E:
Moving the shift lever to any position except D or S (6th, 5th or 4th gear).
for U660E, K111, K111F, K114, K114F:
Moving the shift lever to any position except D or M (6th, 5th or 4th gear).
w/ Shift Paddle Switch:
The transaxle is changed from 4th gear to 3rd, 2nd or 1st gear with the shift paddle switch while the shift lever is in D or M.
Pulling the cruise control switch to CANCEL.
Pushing the cruise control switch to off.
INSPECT RES (RESUME) SWITCH
Push the cruise control switch to on.
Drive the vehicle at a desired speed (between approximately 40 km/h and 200 km/h [25 mph and 125 mph]).
Press the cruise control switch to -SET.
When performing one of the following, check that the cruise control system is canceled and that the normal driving mode is reset.
Depressing the brake pedal.
for Manual Transaxle:
Depressing the clutch pedal.
for U760F, U760E:
Moving the shift lever to any position except D or S (6th, 5th or 4th gear).
for U660F, K111, K111F, K114, K114F:
Moving the shift lever to any position except D or M (6th, 5th or 4th gear).
w/ Shift Paddle Switch:
The transaxle is changed from 4th gear to 3rd, 2nd or 1st gear with the shift paddle switch while the shift lever is in D or M.
Pulling the cruise control switch to CANCEL.
Pushing the cruise control switch to off.
After the cruise control switch is pulled up to +RES at a driving speed of more than 40 km/h (25 mph), check that the vehicle restores the speed before the cancellation.