Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE(for Dual Type) › from 2015.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0059591 SPIRAL CABLE(for Dual Type) G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE(for Dual Type)  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



a.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector


OK:

No defects are found.


If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

NOTICE:

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.


B439933C02
1.146,6.198 1.438,6.417 0.292,0.219 3.271,6.073 3.563,6.292 0.292,0.219 5.208,0.833 5.5,1.052 0.292,0.219 6.021,0.833 6.313,1.052 0.292,0.219 2.396,2.469 2.688,2.688 0.292,0.219 1.396,2.469 1.688,2.688 0.292,0.219 1.063,5.667 1.427,5.667 1.427,5.667 1.885,5.948 true 1.073,5.906 1.438,5.906 1.438,5.906 1.896,6.188 true 1.073,6.615 1.438,6.615 1.438,6.615 1.885,6.438 true 1.073,6.875 1.438,6.875 1.438,6.875 1.885,6.698 true 1.958,5.5 2.75,6.094 true 1.99,5.292 2.229,5.292 2.229,5.292 2.75,5.969 true 1.521,5.115 2.177,5.115 2.177,5.115 2.74,5.833 true 2.823,5.677 2.823,5.115 2.823,5.115 3.094,5.115 true 2.25,7.083 2.25,6.49 2.25,6.49 2.76,6.25 true 2.479,6.833 2.479,6.5 2.479,6.5 2.75,6.406 true 2.823,7.208 2.823,6.552 true 2.99,5.708 3.167,5.271 3.167,5.271 3.542,5.271 true 3,5.823 3.281,5.583 3.281,5.583 3.813,5.583 true 2.99,5.969 3.24,5.781 3.24,5.781 3.469,5.781 true 3,6.094 3.25,5.906 3.25,5.906 3.844,5.906 true 3,6.365 3.25,6.542 3.25,6.542 3.479,6.542 true 2.99,6.552 3.24,6.875 3.24,6.875 3.531,6.875 true 1.198,6.219 1.51,6.417 0.313,0.198 10 false G9 3.333,6.104 3.646,6.302 0.313,0.198 10 false G9 5.292,0.854 5.604,1.052 0.313,0.198 10 false z1 6.094,0.854 6.406,1.052 0.313,0.198 10 false z4 2.469,2.49 2.781,2.688 0.313,0.198 10 false z2 1.469,2.479 1.781,2.677 0.313,0.198 10 false z3 0.833,5.563 1.146,5.76 0.313,0.198 10 false D+ 0.885,5.823 1.198,6.021 0.313,0.198 10 false D- 0.813,6.521 1.125,6.719 0.313,0.198 10 false D2- 0.792,6.802 1.125,6.99 0.333,0.188 10 false D2+ 1.698,5.406 2.313,5.604 0.615,0.198 10 false IL-2 1.656,5.198 2.271,5.396 0.615,0.198 10 false EAU 1.198,5.021 1.813,5.219 0.615,0.198 10 false ECC 3.146,5.021 3.76,5.219 0.615,0.198 10 false CCS 2.125,7.104 2.74,7.302 0.615,0.198 10 false AU2 2.344,6.854 2.958,7.052 0.615,0.198 10 false AU1 2.688,7.24 3.302,7.438 0.615,0.198 10 false SDN 3.604,5.177 4.219,5.375 0.615,0.198 10 false ILL- 3.875,5.49 4.49,5.688 0.615,0.198 10 false IL+2 3.531,5.688 3.844,5.885 0.313,0.198 10 false +DP 3.896,5.802 4.333,6.031 0.438,0.229 10 false +DP2 3.531,6.458 4.146,6.656 0.615,0.198 10 false HO 3.594,6.781 4.208,6.979 0.615,0.198 10 false SUP
*a Component without harness connected
(spiral cable sub-assembly)
- -
V100144

Interlock - -


i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-1 (D+) - z2-2 Always Below 1 Ω
G9-2 (D-) - z2-1
G9-3 (D2-) - z3-1
G9-4 (D2+) - z3-2
G8-1 (CCS) - z4-3 3 Ω or less
G8-2 (ECC) - z1-7
G8-2 (ECC) - z4-4
G8-3 (EAU) - z1-8
G8-4 (IL-2) - z1-9
G8-5 (AU2) - z1-10
G8-6 (AU1) - z1-11
G8-7 (SDN) - z1-12
G8-8 (ILL-) - z4-1
G8-9 (IL+2) - z1-5
G8-9 (IL+2) - z4-2
G8-10 (+DP) - z1-2
G8-11 (+DP2) - z1-3
G8-13 (HO) - z1-1
G8-14 (SUP) - z1-6



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-1 (D+) - z2-2 Always Below 1 Ω
G9-2 (D-) - z2-1
G9-3 (D2-) - z3-1
G9-4 (D2+) - z3-2
G8-1 (CCS) - z4-3 3 Ω or less
G8-2 (ECC) - z1-7
G8-2 (ECC) - z4-4
G8-3 (EAU) - z1-8
G8-4 (IL-2) - z1-9
G8-5 (AU2) - z1-10
G8-6 (AU1) - z1-11
G8-7 (SDN) - z1-12
G8-8 (ILL-) - z4-1
G8-9 (IL+2) - z1-5
G8-9 (IL+2) - z4-2
G8-10 (+DP) - z1-2
G8-11 (+DP2) - z1-3
G8-13 (HO) - z1-1
G8-14 (SUP) - z1-6



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-1 (D+) - z2-2 Always Below 1 Ω
G9-2 (D-) - z2-1
G9-3 (D2-) - z3-1
G9-4 (D2+) - z3-2
G8-1 (CCS) - z4-3 3 Ω or less
G8-2 (ECC) - z1-7
G8-2 (ECC) - z4-4
G8-3 (EAU) - z1-8
G8-4 (IL-2) - z1-9
G8-5 (AU2) - z1-10
G8-6 (AU1) - z1-11
G8-7 (SDN) - z1-12
G8-8 (ILL-) - z4-1
G8-9 (IL+2) - z1-5
G8-9 (IL+2) - z4-2
G8-10 (+DP) - z1-2
G8-11 (+DP2) - z1-3
G8-13 (HO) - z1-1
G8-14 (SUP) - z1-6


If the result is not as specified, replace the spiral cable with sensor sub-assembly.