Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.10
RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049317 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 63353C 1.REMOVE CENTER ROOF HEADLINING PAD

a.
B367336C01
0.771,1.927 1.813,1.927 true 0.698,1.74 0.948,1.406 0.948,1.406 1.427,1.406 true 1.854,1.833 2.167,1.99 0.313,0.156 10 false *1 1.448,1.302 1.76,1.458 0.313,0.156 10 true *2
*1 for Type A
*2 for Type B


Remove the 2 center roof headlining pads.


Hide 63341 2.REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Remove the 5 No. 1 roof silencer pads.

B439329


Hide 63341 3.REMOVE NO. 1 ROOF SILENCER PAD (w/ Sliding Roof)

a.
B337928

Remove the 2 No. 1 roof silencer pads.


Hide 63343 4.REMOVE NO. 3 ROOF SILENCER PAD

a.
B337929

Remove the No. 3 roof silencer pad.


Hide 63351B 5.REMOVE ROOF HEADLINING PAD (for Cold Area)

HINT:

Use the same procedure for both roof headlining pads.


a.
B423651

Remove the roof headlining pad.


Hide 63352D 6.REMOVE NO. 2 ROOF HEADLINING PAD (for Cold Area)

a.
B439328

Remove the No. 2 roof headlining pad.


Hide 81340J 7.REMOVE VANITY LIGHT ASSEMBLY LH

a.
B337937C01
2.771,0.469 2.865,0.313 2.865,0.313 3.021,0.313 false 3.052,0.24 3.25,0.417 0.198,0.177 10 *1
*1 Bulb Holder


Detach the 2 claws and disconnect the bulb holder from the vanity light assembly LH.


b.

Detach the claw and remove the vanity light assembly LH.


Hide 81340H 8.REMOVE VANITY LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 82171 9.REMOVE NO. 1 ROOF WIRE

a.

w/o Sliding Roof:

i.

Turn the 2 connectors approximately 90° clockwise and disconnect them.


ii.

Remove the one-sided tape.


iii.

Remove the remaining No. 1 roof wire from the double-sided tape.


iv.

Remove the remaining double-sided tape.

B438456C01
1.469,0.844 1.781,1 0.313,0.156 10 false *A 1.729,0.802 1.979,0.958 0.25,0.156 10 false *B 0.552,3.219 0.865,3.375 0.313,0.156 10 false *a 1.854,0.583 2.167,0.74 0.313,0.156 10 false *C 1.156,0.885 1.469,1.042 0.313,0.156 10 false *E 2.094,0.5 2.323,0.656 0.229,0.156 10 false *D
*A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
*C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
*E w/ Pre-crash Safety System - -
*a 90° - -
V100146

One-sided Tape - -




b.

w/ Sliding Roof:

i.

Turn the 2 connectors approximately 90° clockwise and disconnect them.


ii.

Remove the one-sided tape.


iii.

Remove the remaining No. 1 roof wire from the double-sided tape.


iv.

Remove the remaining double-sided tape.

B438457C01
1.5,0.781 1.813,0.938 0.313,0.156 10 false *A 1.74,0.74 1.979,0.896 0.24,0.156 10 false *B 1.177,0.802 1.49,0.958 0.313,0.156 10 false *E 0.563,3.052 0.875,3.208 0.313,0.156 10 false *a 1.865,0.521 2.177,0.677 0.313,0.156 10 false *C 2.115,0.427 2.427,0.583 0.313,0.156 10 false *D
*A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
*C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
*E w/ Pre-crash Safety System - -
*a 90° - -
V100146

One-sided Tape - -




Hide 86101J 10.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 11.REMOVE TONNEAU COVER STOPPER SILENCER (w/ Silencer)

HINT:

Use the same procedure for both tonneau cover stopper silencers.


a.
B426258

Remove the tonneau cover stopper silencer.


Hide 12.REMOVE TONNEAU COVER STOPPER

HINT:

Use the same procedure for both tonneau cover stoppers.


a.
B426259

Remove the 2 screws and tonneau cover stopper.