Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR OUTSIDE MOULDING › from 2015.10
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050284 FRONT DOOR OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR OUTSIDE MOULDING  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75793C 1.INSTALL FRONT DOOR UPPER OUTSIDE MOULDING PAD

a.

Clean the front door upper outside moulding pad installation surface with a non-residue solvent.


b.

Apply primer to the front door upper outside moulding pad installation area on the front door outside moulding.

NOTICE:

Apply primer evenly so that there are no uncoated areas.



c.

Remove the peeling paper on a new front door upper outside moulding pad while making sure not to touch the adhesional surface.


d.
B340228

Install a new front door upper outside moulding pad in the position shown in the illustration.

NOTICE:
·

Press the double-sided tape on the front door upper outside moulding pad firmly to attach.

·

After the primer dries (3 minutes or more), install the front door upper outside moulding pad.

·

After applying primer, reapply primer after 24 hours elapse.




Hide 75787B 2.INSTALL FRONT DOOR OUTSIDE MOULDING PAD

HINT:

When installing the front door outside moulding pad, heat the front door outside moulding using a heat light.


Standard:
Item Temperature
Front Door Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front door outside moulding excessively.


a.

Clean the front door outside moulding surface.

i.

Using a heat light, heat the front door outside moulding surface.


ii.

Remove the double-sided tape from the front door outside moulding.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B437065

Install a new front door outside moulding pad.

i.

Using a heat light, heat the front door outside moulding.


ii.

Remove the peeling paper from the face of the front door outside moulding pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front door outside moulding pad as shown in the illustration.

HINT:

Press the front door outside moulding pad firmly to install it.




Hide 75794C 3.INSTALL FRONT DOOR REAR OUTSIDE MOULDING PAD

HINT:

When installing the front door rear outside moulding pad, heat the front door outside moulding using a heat light.


Standard:
Item Temperature
Front Door Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front door outside moulding excessively.


a.

Clean the front door outside moulding surface.

i.

Using a heat light, heat the front door outside moulding surface.


ii.

Remove the double-sided tape from the front door outside moulding.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B437066

Install 6 new front door rear outside moulding pads.

i.

Using a heat light, heat the front door outside moulding.


ii.

Remove the peeling paper from the face of the 6 front door rear outside moulding pads.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the 6 front door rear outside moulding pads as shown in the illustration.

HINT:

Press the front door rear outside moulding pad firmly to install it.




Hide 4.INSTALL NO. 2 OUTSIDE MOULDING SEAL

HINT:

When installing the No. 2 outside moulding seal, heat the front door outside moulding using a heat light.


Standard:
Item Temperature
Front Door Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front door outside moulding excessively.


a.

Clean the front door outside moulding surface.

i.

Using a heat light, heat the front door outside moulding surface.


ii.

Remove the double-sided tape from the front door outside moulding.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B437067

Install 2 new No. 2 outside moulding seals.

i.

Using a heat light, heat the front door outside moulding.


ii.

Remove the peeling paper from the face of the 2 No. 2 outside moulding seals.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the 2 No. 2 outside moulding seals as shown in the illustration.

HINT:

Press the No. 2 outside moulding seal firmly to install it.