Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 8 Sensor Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232443 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 8 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 8 Sensor Type)  Clearance Warning Buzzer Circuit  


DESCRIPTION

The No. 1 clearance warning buzzer is an ECU-operated buzzer that sounds when it receives a pulsed digital signal from the ECU. The ECU operates the buzzer so that it sounds in a pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E309542E04
0.729,0.302 1.042,0.5 0.313,0.198 10 false IG 2.865,0.375 3.177,0.573 0.313,0.198 10 false CBZ 2.948,1.01 3.26,1.208 0.313,0.198 10 false EF 3.25,0.365 3.563,0.563 0.313,0.198 10 false 14 3.25,1 3.563,1.198 0.313,0.198 10 false 13 4.667,0.365 4.979,0.563 0.313,0.198 10 false 1 4.677,1 4.99,1.198 0.313,0.198 10 false 2 4.885,0.375 5.198,0.573 0.313,0.198 10 false Z+ 4.896,1 5.208,1.198 0.313,0.198 10 false Z- 4.573,1.573 4.885,1.771 0.313,0.198 10 false G34 4.573,1.74 6.802,1.99 2.229,0.25 10 false No. 1 Clearance Warning Buzzer 0.74,2.063 1.167,2.26 0.427,0.198 10 false G166 0.75,2.229 3.073,2.49 2.323,0.26 10 false Clearance Warning ECU Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer Clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the ignition switch is ON

OK:

The No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the G166 clearance warning ECU assembly connector.


b.

Disconnect the G34 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G166-14 (CBZ) - G34-1 (Z+) Always Below 1 Ω
G166-13 (EF) - G34-2 (Z-) Always Below 1 Ω
G166-14 (CBZ) or G34-1 (Z+) - Body ground Always 10 kΩ or higher
G166-13 (EF) or G34-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Clearance Sonar
Tester Display Test Part Control Range Diagnostic Note
Buzzer Clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the ignition switch is ON

OK:

The No. 1 clearance warning buzzer sounds.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

B

C