Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E341398E01
4.979,2.719 5.292,2.917 0.313,0.198 10 false a2 4.99,2.906 7.156,3.208 2.167,0.302 10 false Parking Assist ECU 0.167,0.073 5.063,0.271 4.896,0.198 10 false from Engine Stop and Start ECU*1 1.302,0.896 3.448,1.094 2.146,0.198 10 false from Battery*2 0.792,1.333 4,1.531 3.208,0.198 10 false from IG1 NO.1 Relay*2 1.083,1.719 3.531,1.917 2.448,0.198 10 false from ACC Relay*2 3.438,1.896 3.896,2.094 0.458,0.198 10 false ACC 5.333,1.76 5.792,1.958 0.458,0.198 10 false ACC 3.177,1.052 4.708,1.25 1.531,0.198 10 false ECU-B NO.1 3.198,1.49 4.729,1.688 1.531,0.198 10 false ECU-IG NO.2 0.115,2.896 5.469,3.094 5.354,0.198 10 false *1: w/ Engine Stop and Start System 0.135,3.302 5.49,3.5 5.354,0.198 10 false *2: w/o Engine Stop and Start System 5.323,2.156 5.938,2.354 0.615,0.198 10 false GND1 5.333,1.333 5.792,1.531 0.458,0.198 10 false IG 5.344,0.927 5.802,1.125 0.458,0.198 10 false +B 5.073,0.771 5.229,0.969 0.156,0.198 10 false 2 5.063,1.167 5.219,1.365 0.156,0.198 10 false 6 5.073,1.583 5.229,1.781 0.156,0.198 10 false 1 5.073,1.99 5.229,2.188 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


HINT:
·

The parking assist ECU is connected to other ECUs via CAN communication or AVC-LAN communication.

·

w/ Navigation System:

If the parking assist ECU does not operate due to a power source problem, a navigation system DTC may be stored due to an AVC-LAN communication interruption.

·

w/ Audio and Visual System (for Radio and Display Type):

If the parking assist ECU does not operate due to a power source problem, an audio and visual system DTC may be stored due to an AVC-LAN communication interruption.

·

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
C280345C22
1.458,0.313 1.875,0.563 0.417,0.25 0.469,1.948 0.656,1.948 0.656,1.948 1.01,1.323 true 2.833,0.552 2.667,0.552 2.667,0.552 2.292,1.104 true 0.344,0.479 0.531,0.479 0.531,0.479 1.135,1.073 true 0.406,1.563 0.594,1.563 0.594,1.563 0.885,1.146 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.333 1.885,0.531 0.313,0.198 10 false a2 0.271,1.875 0.771,2.042 0.5,0.167 10 false IG 2.875,0.469 3.375,0.635 0.5,0.167 10 false GND1 0.135,0.396 0.635,0.563 0.5,0.167 10 false +B 0.094,1.479 0.594,1.646 0.5,0.167 10 false ACC
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-3 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Engine Stop and Start System

*2: w/ Engine Stop and Start System

a2-2 (+B) - a2-3 (GND1) Always 11 to 14 V*1
10 to 16 V*2
a2-1 (ACC) - a2-3 (GND1) Engine switch on (ACC) 11 to 14 V*1
10 to 16 V*2
10 to 16 V*2
a2-6 (IG) - a2-3 (GND1) Engine switch on (IG) 11 to 14 V*1
10 to 16 V*2



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR