Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM D

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  FREEZE FRAME DATA  


CHECK FREEZE FRAME DATA


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

e.

According to the GTS display, select a DTC that stored freeze frame data.


f.

Read the freeze frame data recorded when the DTC was stored.

Body Electrical > Pre-Crash 2
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-crash safety system switch status ON or OFF ON: Pre-crash safety system function disabled due to switch operation
OFF: Pre-crash safety system function enabled due to switch operation
-
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function Valid or Inval Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash brake assist not activated
Standby: Pre-crash brake assist standby
Assist Lv1: Pre-crash brake assist activated
Assist Lv2: Pre-crash brake assist activated
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake - - - Not applicable to the vehicle
Brake Assist Standby Supplemental brake pressure signal ON or OFF ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
-
Pre-Crash Brake Control Pre-crash brake operational status ON or OFF ON: Pre-crash brake operating
OFF: Pre-crash brake not operating
-
AVS Start - - - Not applicable to the vehicle
VGRS Start - - - Not applicable to the vehicle
PBA Control Pre-crash brake assist operational status Valid or Invalid Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible
-
Pre-Crash Safety Brake Ind Pre-crash safety system alarm warning message status ON or OFF ON: Pre-crash safety system "BRAKE!" alert on
OFF: Pre-crash safety system "BRAKE!" alert off
"BRAKE!" is displayed
PCS Crash Alarm Buzzer Skid control buzzer status ON or OFF ON: Skid control buzzer sounds
OFF: Skid control buzzer does not sound
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
-
Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history ON or OFF ON: History of vertical misalignment
OFF: No history of vertical misalignment
-
Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history ON or OFF ON: History of horizontal misalignment
OFF: No history of horizontal misalignment
-
Front Recognition Camera-Malfunction History Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) ON or OFF ON: History of malfunction
OFF: No history of malfunction
-
Control Mode ECU control mode status Normal or Check Mode Normal: Normal operation
Check Mode: Operating in Control Mode
-
PCS Operation State Retention Setting Displays the setting of the PCS Operation State Retention Setting customize setting ON or OFF ON: PCS Operation State Retention Setting customize setting is set to ON
OFF: PCS Operation State Retention Setting customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to OFF
-