Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-crash safety system switch status ON or OFF ON: Pre-crash safety system switch on
OFF: Pre-crash safety system switch off
-
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function Valid or Inval Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash brake assist not activated
Standby: Pre-crash brake assist standby
Assist Lv1: Pre-crash brake assist activated
Assist Lv2: Pre-crash brake assist activated
Signal status changes when the pre-crash brake assist is activated before a collision (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake - - - Not applicable to the vehicle
Brake Assist Standby - - - This item is displayed on the GTS but is not used.
Pre-Crash Brake Control Pre-crash brake operational status ON or OFF ON: Pre-crash brake operating
OFF: Pre-crash brake not operating
-
AVS Start - - - Not applicable to the vehicle
VGRS Start - - - Not applicable to the vehicle
PBA Control Pre-crash brake assist operational status Valid or Invalid Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible
-
Pre-Crash Safety Brake Ind Pre-crash safety system alarm warning message status ON or OFF ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Crash Alarm Buzzer Skid control buzzer status ON or OFF ON: Skid control buzzer sounds
OFF: Skid control buzzer does not sound
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
-
Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history ON or OFF ON: History of vertical misalignment
OFF: No history of vertical misalignment
-
Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history ON or OFF ON: History of horizontal misalignment
OFF: No history of horizontal misalignment
-
Front Recognition Camera-Malfunction History Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) ON or OFF ON: History of malfunction
OFF: No history of malfunction
-
Control Mode ECU control mode status Normal or Check Mode Normal: Normal operation
Check Mode: Operating in Control Mode
-
PCS Operation State Retention Setting Displays the setting of the PCS Operation State Retention Setting customize setting ON or OFF ON: PCS Operation State Retention Setting customize setting is set to ON
OFF: PCS Operation State Retention Setting customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF ON: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to ON
OFF: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to OFF
-

f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Relay Output Stop light control relay output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform Active Test according to the display on the GTS.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the GTS.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON or OFF Test possible with ignition switch ON, vehicle stopped

f.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


g.

Perform Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Precrash PCS warning indicator ON or OFF -

h.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


i.

Perform Active Test according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON or OFF Test possible at vehicle speed of 0 km/h (0 mph)