The forward recognition camera receives vehicle stability signals from the yaw rate sensor assembly. If the yaw rate sensor assembly detects an abnormal yaw rate sensor signal or yaw rate sensor assembly power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA4 | Yaw Rate Sensor Circuit | 2 seconds after the ignition switch is turned ON, the vehicle speed is 1 km/h or more and a signal from the yaw rate sensor indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more. | ·
Vehicle stability control system ·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Forward recognition camera |
| C1AA5 | Yaw Rate Sensor Power Supply Voltage Circuit | 2 seconds after the ignition switch is turned ON, the vehicle speed is 1 km/h or more and a signal from the yaw rate sensor indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more. | ·
Vehicle stability control system ·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
If the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 7 seconds or more.
Drive the vehicle at 1 km/h (0.6 mph) or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA4 or C1AA5 is output. | A |
| DTC C1AA4 and C1AA5 are not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Adjust the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 7 seconds or more.
Drive the vehicle at 1 km/h (0.6 mph) or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA4 or C1AA5 is output. | A |
| DTC C1AA4 and C1AA5 are not output. | B |
A
B