Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226195 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Main Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert main switch signal from the lane departure alert main switch and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

C347909E01
2.094,1.531 3.5,1.948 1.406,0.417 10 false Lane Departure Alert Main Switch 2.083,1.375 2.698,1.573 0.615,0.198 10 false G165 2.948,0.938 3.406,1.135 0.458,0.198 10 false ECU 2.198,0.948 2.656,1.146 0.458,0.198 10 false GND 3.333,0.927 3.49,1.125 0.156,0.198 10 false 6 2.031,0.938 2.188,1.135 0.156,0.198 10 false 3 4.208,2.125 4.823,2.323 0.615,0.198 10 false G168 4.208,2.271 5.583,2.74 1.375,0.469 10 false Driving Support ECU Assembly 4.313,0.927 4.469,1.125 0.156,0.198 10 false 5 4.5,1.052 5.115,1.25 0.615,0.198 10 false PBSW 4.833,1.51 5.448,1.708 0.615,0.198 10 false CA1N 4.833,0.844 5.448,1.042 0.615,0.198 10 false CA1P 6.219,1.51 6.833,1.708 0.615,0.198 10 false CANL 6.219,0.854 6.833,1.052 0.615,0.198 10 false CANH 5.302,0.698 5.458,0.896 0.156,0.198 10 false 8 5.302,1.365 5.458,1.563 0.156,0.198 10 false 9 5.885,2.115 6.344,2.313 0.458,0.198 10 false Q17 5.896,2.271 7.156,2.771 1.26,0.5 10 false Forward Recognition Camera 6.052,0.708 6.208,0.906 0.156,0.198 10 false 6 5.979,1.354 6.292,1.552 0.313,0.198 10 false 12 0.604,3.323 2.354,3.49 1.75,0.167 10 false : CAN Communication Line

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



A

2.CHECK DTC (HEALTH CHECK)

B

2.CHECK DTC (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

3.INSPECT LANE DEPARTURE ALERT MAIN SWITCH

B

GO TO DTC CHART

3.INSPECT LANE DEPARTURE ALERT MAIN SWITCH

OK

4.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT MAIN SWITCH - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT MAIN SWITCH - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the G165 lane departure alert main switch connector.


b.

Disconnect the G168 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G165-6 (ECU) - G168-5 (PBSW) Always Below 1 Ω
G165-6 (ECU) or G168-5 (PBSW) - Body ground Always 10 kΩ or higher
G165-3 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR