Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226195 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

B437481E04
5.021,2.5 7.021,2.719 2,0.219 10 false Forward Recognition Camera 5.021,2.333 5.479,2.531 0.458,0.198 10 false Q17 5.573,2.083 6.031,2.281 0.458,0.198 10 false GND 5.594,0.771 6,1.031 0.406,0.26 10 false IGB 5.406,0.656 5.563,0.854 0.156,0.198 10 false 7 5.344,1.969 5.656,2.167 0.313,0.198 10 false 10 0.854,1.333 2.99,1.552 2.135,0.219 10 false from Engine Stop and Start ECU 0.177,3.073 2.177,3.302 2,0.229 10 false *1: w/o Stop and Start System 0.177,3.365 2.177,3.594 2,0.229 10 false *2: w/ Stop and Start System 0.885,0.76 3.948,0.958 3.063,0.198 10 false from IG1-NO. 1 Relay 3.167,0.927 4.24,1.104 1.073,0.177 10 false ECU-IG1 NO. 2 4.156,0.667 4.469,0.865 0.313,0.198 10 false *1 4.167,1.219 4.479,1.417 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
C265807C03
0.719,1.677 1.073,1.927 0.354,0.25 1.344,2 0.979,2.427 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.771,1.74 1.229,1.938 0.458,0.198 10 false Q17 0.698,2.542 1.313,2.74 0.615,0.198 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the Q17 forward recognition camera connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q17-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
C265807C04
0.719,1.677 1.073,1.927 0.354,0.25 1.854,2 2.188,2.49 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.771,1.74 1.229,1.938 0.458,0.198 10 false Q17 2.115,2.542 2.729,2.74 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the Q17 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR