Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the dynamic radar cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Turn the cruise control switch (ON/OFF) on.


g.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 5405

h.

Check the amount of misalignment and make a note.


i.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 5406

j.

Check the amount of offset and make a note.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check for the CAN communication system.

for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM

for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTCs*

NG

5.CHECK FOR DTCs*

Refer to DTC Check / Clear.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

a.

Check for DTCs and note any codes that are output.

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391
Powertrain > Radar Cruise2 > Trouble Codes
50001 197


b.

Clear the DTCs.

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Clear DTCs
50002 74
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Clear DTCs
50002 239
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

iii.

for 2WW:

Powertrain > Cruise Control > Clear DTCs
50002 391
Powertrain > Radar Cruise2 > Clear DTCs
50002 197


c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391
Powertrain > Radar Cruise2 > Trouble Codes
50001 197


Result:
Result Proceed to
DTC does not reoccur A
DTC reoccurs B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.ADJUST, REPAIR OR REPLACE
7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

9.CONFIRMATION TEST
9.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END