Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Millimeter Wave Radar Sensor Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to terminal IGB of the millimeter wave radar sensor assembly.

This circuit provides power to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly emits radio waves towards an object in front and measures the distance and direction of the object by receiving the beam reflections. Based on the reflections, the sensor calculates the difference in speed between the vehicle and the object in front. This data is transmitted to the driving support ECU assembly.

WIRING DIAGRAM

B437481E15
5.323,2.646 6.74,3.156 1.417,0.51 10 false Millimeter Wave Radar Sensor Assembly 5.323,2.427 5.781,2.625 0.458,0.198 10 false Z6 5.573,2.083 6.135,2.302 0.563,0.219 10 false SGND 5.594,0.771 6,1.031 0.406,0.26 10 false IGB 5.365,0.667 5.521,0.865 0.156,0.198 10 false 8 5.385,1.969 5.698,2.167 0.313,0.198 10 false 1 0.854,1.333 2.99,1.552 2.135,0.219 10 false from Engine Stop and Start ECU 0.177,3.073 2.177,3.302 2,0.229 10 false *1: w/o Stop and Start System 0.177,3.365 2.177,3.594 2,0.229 10 false *2: w/ Stop and Start System 0.885,0.76 3.948,0.958 3.063,0.198 10 false from IG1 NO. 2 Relay 3.188,0.927 4.26,1.104 1.073,0.177 10 false ECU-IG NO. 3 4.156,0.667 4.469,0.865 0.313,0.198 10 false *1 4.167,1.219 4.479,1.417 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
a.
E325539C42
1.563,0.156 1.938,0.385 0.375,0.229 2.479,1.771 1.958,1.25 true 1.646,0.198 2.104,0.396 0.458,0.198 10 false Z6 2.542,1.719 3,1.917 0.458,0.198 10 false IGB 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the Z6 millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Z6-8 (IGB) - Bodyground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2



d.

Reconnect the Z6 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the Z6 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Check for Open:
Tester Connection Condition Specified Condition
Z6-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the Z6 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR