Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the driving support ECU assembly. The driving support ECU assembly determines information about the vehicle in front based on data from the radar sensor, and then decides how much acceleration and/or deceleration is needed to maintain the set distance. The driving support ECU assembly also requests the skid control ECU to apply brakes and sounds the skid control buzzer.

WIRING DIAGRAM

B437481E06
5.021,2.5 7.021,2.719 2,0.219 10 false Driving Support ECU Assembly 5.021,2.333 5.479,2.531 0.458,0.198 10 false G168 5.573,2.083 6.031,2.281 0.458,0.198 10 false GND 5.594,0.771 6,1.031 0.406,0.26 10 false B 5.406,0.656 5.563,0.854 0.156,0.198 10 false 7 5.344,1.969 5.656,2.167 0.313,0.198 10 false 28 0.854,1.333 2.99,1.552 2.135,0.219 10 false from Engine Stop and Start ECU 0.177,3.073 2.177,3.302 2,0.229 10 false *1: w/o Stop and Start System 0.177,3.365 2.177,3.594 2,0.229 10 false *2: w/ Stop and Start System 0.885,0.76 3.948,0.958 3.063,0.198 10 false from IG1 NO. 1 Relay 3.167,0.927 4.24,1.104 1.073,0.177 10 false ECU-IG NO. 2 4.156,0.667 4.469,0.865 0.313,0.198 10 false *1 4.167,1.219 4.479,1.417 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E323582C55
1.563,0.188 2,0.427 0.438,0.24 0.875,0.323 1.24,0.958 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 1.625,0.24 2.24,0.438 0.615,0.198 10 false G168 0.74,0.219 0.896,0.417 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G168 driving support ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

G168-7 (B) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the G168 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-28 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR