Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226196 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


E256359C08
1.708,0.729 2.146,0.979 0.438,0.25 1.802,0.781 2.26,0.979 0.458,0.198 10 false Q17

a.

Disconnect the Q17 forward recognition camera connector.

NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the Q17 forward recognition camera connector.




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q17-7 (IGB) - Body ground GR - Body ground Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
Q17-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the Q17 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q17-5 (CA1P) - Q17-10 (GND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q17-11 (CA1N) - Q17-10 (GND) LG - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
Q17-6 (CANH) - Q17-10 (GND) L - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q17-12 (CANL) - Q17-10 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)


e.
A292386E03
1.344,1.917 2.313,2.146 0.969,0.229 10 false 10 μsec./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 false 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 false GND

WAVEFORM 1

i.

CAN communication signal

Item Content
Terminal Name Between Q17-5 (CA1P) and Q17-10 (GND)
Between Q17-6 (CANH) and Q17-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




f.
A292387E07
3,1.375 3.344,1.573 0.344,0.198 10 false GND 2.781,0.26 3.417,0.458 0.635,0.198 10 false 1 V/DIV. 1.375,1.885 2.323,2.135 0.948,0.25 10 false 10 μsec./DIV.

WAVEFORM 2

i.

CAN communication signal

Item Content
Terminal Name Between Q17-11 (CA1N) and Q17-10 (GND)
Between Q17-12 (CANL) and Q17-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.