Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226196 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1A10  Front Radar Sensor  


DESCRIPTION

The forward recognition camera uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

When the forward recognition camera receives information that there is a malfunction in the millimeter wave radar sensor assembly, DTC C1A10 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A10 Front Radar Sensor 2 seconds after the ignition switch is turned ON, a signal from the millimeter wave radar sensor assembly indicating that there is an internal malfunction in millimeter wave radar sensor assembly is detected by the forward recognition camera for 5 seconds or more.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

2.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
2.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.


e.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

f.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

1.

Wait 7 seconds or more after turning the ignition switch to ON.




g.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1A10 is not output A
DTC C1A10 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA