Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0051217 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (multiplex network body ECU) is supplied via the door control battery.

WIRING DIAGRAM

B375840E05
5.656,0.948 6.271,1.146 0.615,0.198 10 false BECU 5.375,2.99 7.031,3.5 1.656,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 5.385,2.833 6,3.031 0.615,0.198 10 false A 3.771,0.833 4.385,1.031 0.615,0.198 10 false 41 5.417,0.833 6.031,1.031 0.615,0.198 10 false 30 3.802,1.417 4.417,1.615 0.615,0.198 10 false 3D 3.802,1.573 5.417,2.052 1.615,0.479 10 false Instrument Panel Junction Block Assembly 2.688,0.948 3.302,1.146 0.615,0.198 10 false EDOR 3.177,0.833 3.792,1.031 0.615,0.198 10 false 3 2.385,0.667 3,0.865 0.615,0.198 10 false BATB 2.198,0.563 2.813,0.76 0.615,0.198 10 false 5 2.208,1.198 2.823,1.396 0.615,0.198 10 false 4 2.385,1.281 3,1.479 0.615,0.198 10 false BECU 1.573,0.802 2.26,0.969 0.688,0.167 10 false D/L NO.1 1.49,1.427 2.49,1.594 1,0.167 10 false ECU-B NO.1 0.177,0.615 1.281,0.844 1.104,0.229 10 false from Battery 2.385,1.958 3,2.156 0.615,0.198 10 false GND1 2.208,1.875 2.823,2.073 0.615,0.198 10 false 2 2.125,2.583 2.74,2.781 0.615,0.198 10 false N37 2.135,2.76 3.635,3.042 1.5,0.281 10 false Door Control Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - BATTERY AND BODY GROUND)
a.
B377768C23
0.323,0.948 0.823,1.281 0.5,0.333 1.813,1.042 1.969,0.115 1.969,0.115 2.219,0.115 true 1.979,1.042 2.292,0.344 2.292,0.344 2.542,0.344 true 1.469,1.052 1.229,0.25 1.229,0.25 0.979,0.25 true 2.26,0.042 2.875,0.24 0.615,0.198 10 false BECU 0.448,1.031 1.063,1.229 0.615,0.198 10 false N37 2.594,0.281 3.208,0.479 0.615,0.198 10 false BATB 0.573,0.177 1.188,0.375 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Door Control Battery)


Disconnect the door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N37-4 (BECU) - Body ground Always 11 to 14 V
N37-5 (BATB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N37-2 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the N37 door control battery connector.


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N37-3 (EDOR) - 3D-41 Always Below 1 Ω
N37-3 (EDOR) or 3D-41 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B375843C10
1.854,1.083 2.354,1.333 0.5,0.25 5.49,0.823 5.99,1.073 0.5,0.25 3.323,2.167 3.573,2.167 3.573,2.167 3.656,1.667 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.063,1.135 2.521,1.333 0.458,0.198 10 false A 2.896,2.104 3.354,2.302 0.458,0.198 10 false BECU 5.656,0.875 6.115,1.073 0.458,0.198 10 false 3D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-30 (BECU) - 3D-41 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)

NG

4.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Turn the engine switch off.


b.

Remove the ECU-B NO. 1 fuse from the engine room relay block. and leave the vehicle as is for 50 minutes.


c.

Leave the vehicle as is for 30 minutes (wait until the door control battery is discharged).

HINT:

Discharge time is reduced when the door control battery is not fully charged.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N37-3 (EDOR) - Body ground Engine switch off Below 2 V



e.

Install the ECU-B NO.1 fuse to the engine room relay block.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N37-3 (EDOR) - Body ground Engine switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE DOOR CONTROL BATTERY