Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation receiver assembly via this circuit.

WIRING DIAGRAM

E281004E15
2.073,0.615 2.229,0.813 0.156,0.198 10 false 2 2.073,1.198 2.229,1.396 0.156,0.198 10 false 3 4.958,0.625 5.115,0.823 0.156,0.198 10 false 2 4.969,1.167 5.125,1.365 0.156,0.198 10 false 3 0.135,2.125 0.906,2.333 0.771,0.208 10 false *1: for RHD 5.156,2.01 6.406,2.385 1.25,0.375 10 false Navigation Receiver Assembly 0.177,0.969 0.729,1.177 0.552,0.208 10 false G145 0.188,1.135 1.073,1.729 0.885,0.594 10 false No. 1 Stereo Jack Adapter Assembly 1.604,0.781 2.156,0.99 0.552,0.208 10 false UDO- 1.604,1.313 2.156,1.521 0.552,0.208 10 false UDO+ 5.188,0.698 5.74,0.906 0.552,0.208 10 false UDO-*1 5.198,1.438 5.75,1.646 0.552,0.208 10 false US1+*2 5.188,0.885 5.74,1.094 0.552,0.208 10 false US1-*2 5.188,1.24 5.74,1.448 0.552,0.208 10 false UDO+*1 5.667,1.823 6.219,2.031 0.552,0.208 10 false G197*2 5.146,1.833 5.698,2.042 0.552,0.208 10 false G149*1 0.146,2.406 0.917,2.615 0.771,0.208 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G149*1 or G197*2 navigation receiver assembly connector.

*1: for RHD

*2: for LHD



b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G149-2 (UDO-) - G145-2 (UDO-) Always Below 1 Ω
G149-3 (UDO+) - G145-3 (UDO+) Always Below 1 Ω
G149-2 (UDO-) - Body ground Always 10 kΩ or higher
G149-3 (UDO+) - Body ground Always 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G197-2 (US1-) - G145-2 (UDO-) Always Below 1 Ω
G197-3 (US1+) - G145-3 (UDO+) Always Below 1 Ω
G197-2 (US1-) - Body ground Always 10 kΩ or higher
G197-3 (US1+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR