Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2015.10
RM3090E _54 Brake _008770 BRAKE (REAR) _0049554 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 47319F 3.DISCONNECT REAR FLEXIBLE HOSE LH

C127076

a.

Remove the union bolt and gasket.


b.

Disconnect the flexible hose from the brake cylinder.


Hide 4.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C265922C01
0.792,2.323 0.51,2.167 0.51,2.167 0.365,2.167 true 1.396,2.625 2.063,2.844 2.063,2.844 2.25,2.844 true 0.167,2.094 0.417,2.344 0.25,0.25 10 false *a 2.292,2.792 2.531,2.979 0.24,0.188 10 false *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 04466 5.REMOVE REAR DISC BRAKE PAD KIT

a.

Remove the 2 disc brake pads from the rear disc brake cylinder mounting.


Hide 6.REMOVE REAR ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims from each rear disc brake pad.


Hide 04466 7.REMOVE PAD WEAR INDICATOR PLATE

a.

Remove the pad wear indicator plates from the rear disc brake pads.


Hide 8.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.

Remove the 2 pad support plates from the disc brake cylinder mounting.


Hide 9.REMOVE REAR DISC BRAKE CYLINDER MOUNTING LH

a.

Remove the 2 bolts and disc brake cylinder mounting from the rear axle.


Hide 10.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C211028C01
1.104,0.354 1.573,0.177 1.573,0.177 1.781,0.177 false 1.25,1.063 1,1.385 1,1.385 0.792,1.385 false 1.823,0.115 2.083,0.302 0.26,0.188 10 false *1 0.604,1.323 0.865,1.51 0.26,0.188 10 false *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear Disc Brake Rear Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear disc brake rear cylinder slide pin from the disc brake cylinder mounting.


Hide 11.REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSH

a.
C127071C03
2.292,1.479 2.427,0.802 2.427,0.802 2.688,0.802 false 2.719,0.719 2.906,0.885 0.188,0.167 10 *a
*a Protective tape


Using a screwdriver, remove the rear disc brake cylinder slide bush from the rear disc brake rear cylinder slide pin.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Do not damage the rear disc brake rear cylinder slide pin.



Hide 12.REMOVE REAR DISC BRAKE BUSH DUST BOOT

a.
C127299

Remove the 2 rear disc brake bush dust boots from the disc brake cylinder mounting.


Hide 42491 13.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Remove the shoe adjusting hole plug from the rear disc.


Hide 42431 14.REMOVE REAR DISC

a.
C129072C01
1.75,1.052 2.354,0.219 false 1.771,1.198 2.354,0.219 2.354,0.219 2.729,0.219 false 2.75,0.125 3.042,0.417 0.292,0.292 10 false *a
*a Matchmark


Put matchmarks on the disc and axle hub.


b.

Release the parking brake.


c.
C127304

Turn the shoe adjuster until the disc turns freely, and then remove the disc.


d.

Install the shoe adjusting hole plug to the rear disc.