Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B341520E06
0.771,0.156 1.771,0.354 1,0.198 10 false from Battery 1.167,1.125 1.677,1.313 0.51,0.188 10 false HORN 2.229,1.917 3.104,2.125 0.875,0.208 10 false HORN Relay 2.125,0.344 3,0.552 0.875,0.208 10 false HORN Relay 2.031,0.813 2.177,1.01 0.146,0.198 10 false 1 2.948,0.813 3.094,1.01 0.146,0.198 10 false 2 2.031,1.438 2.177,1.635 0.146,0.198 10 false 5 2.938,1.448 3.083,1.646 0.146,0.198 10 false 3 4.448,0.813 4.75,1.031 0.302,0.219 10 false 36 4.469,1.344 4.771,1.563 0.302,0.219 10 false 39 4.823,0.948 5.125,1.167 0.302,0.219 10 false 3B 4.833,1.458 5.135,1.677 0.302,0.219 10 false 3D 5.917,0.948 6.219,1.167 0.302,0.219 10 false A 5.885,0.729 6.125,0.875 0.24,0.146 10 false 28 6.229,0.604 6.74,0.792 0.51,0.188 10 false HORN 4.802,2.021 5.844,2.521 1.042,0.5 10 false Instrument Panel Junction Block Assembly 4.875,4.021 6.302,4.375 1.427,0.354 10 false to Steering Pad Switch Assembly 5.917,3.271 7.063,3.646 1.146,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.271,4.802 5.417,5.156 1.146,0.354 10 false High Pitched Horn Assembly 4.271,4.625 4.583,4.792 0.313,0.167 10 false A25 2.615,4.677 3.615,4.844 1,0.167 10 false A27*1, A89*2 2.594,4.865 3.729,5.229 1.135,0.365 10 false Low Pitched Horn Assembly 2.229,4.469 2.479,4.646 0.25,0.177 10 false 1 3.885,4.458 4.042,4.656 0.156,0.198 10 false 1 0.146,4.948 7.156,5.24 7.01,0.292 10 false *1: Except Korea 0.146,5.24 7.156,5.531 7.01,0.292 10 false *2: for Korea

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.


Result:
Proceed to
Horns sound
Horns do not sound



Horns sound

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

Horns do not sound

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

B341519N01
1.229,0.25 1.656,0.469 0.427,0.219 4.823,0.292 5.25,0.51 0.427,0.219 5.979,0.75 6.115,0.75 6.115,0.75 6.24,1.198 false 4.979,0.323 5.292,0.521 0.313,0.198 10 A 1.344,0.281 1.656,0.479 0.313,0.198 10 3B 5.521,0.677 6.156,0.875 0.635,0.198 10 HORN

Standard Resistance:
Tester Connection Condition Specified Condition
3B-36 - A-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY